|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
|
|
29-12-2008, 06:44 PM
|
#1 | ||
|
Tyre Shredn
Join Date: May 2007
Location: hillside
Posts: 162
|
ey guys i want to connect elec water & oil guages.
can i just put the water sensor into the radiator hose? or is there away to connect it to the ecu?? because when you open the diagnostics in the lcd piece on the dash is shows water temp?? also for the oil sender for the guage were can i put that. i was told there is a plate you can get which goes between the block and oil filter and you scraw the sensor into that. but i dont think thats correct. |
||
|
|
|
29-12-2008, 07:19 PM
|
#2 | ||
|
FF.Com.Au Hardcore
Join Date: May 2006
Location: Perth, South
Posts: 3,064
|
the water temp sensor you will probably have to put into the hose. i think there is some sort of adaptor that you acn use, you cut a chunk of the hose out and put this alloy thing in there, it has a thread tapped into it for fitting a temp sensor. the factory one will probably be a different resistance to that one, so it won't work properly or at all.
as for the oil sender, yes, there is a plate you an put there. you can also use them to run an engine oil cooler off. have a look on ebay, and probably performance shops. it has a threaded section that screws onto the thread in the block that normally mounts the filter, and an o ring on the top to seal it to the block, then the oil filter mounts as normal. i think most / all of the t series cars ran these from the factory, but used a different oil filter, a smaller one i think, i have a feeling some of the 220kw xr8's did too this gives you an idea of what they look like http://cgi.ebay.com.au/NEW-OIL-COOLE...3286.m20.l1116 and this is the spacer thing you were told about http://cgi.ebay.com.au/Nissan-Sandwi...3286.m63.l1177 |
||
|
|
|
|
29-12-2008, 08:50 PM
|
#3 | ||
|
Boost Addict
Join Date: Jan 2005
Location: North Brisbane
Posts: 1,151
|
the aus do not have a water temp sensor as such, instead a head temp sensor, which doubles for water temp. i would just purchase and EF-L thermostat housing and fit the aftermarket water temp sonsor into that (thats where they used to be).
as for oil pressure, go to pirtek and purchase a t-adapter for the oil pressure switch and fit the oil pressure sender into that. (next to oil filter on block)
__________________
N12 Pulsar - sold Gen1 Liberty Turbo - sold VP Commodore Turbo - sold LN65 Hilux Turbo - sold EL31 Corolla Turbo - sold Ford AU Ute Turbo - sold Ford AU XR8 Sedan - 5.4l V8 Turbo (in the build) Ford BA XR6T Ute - daily driver Ford FG XR6T Sedan - cruiser do you see a general trend? I DO  Can't live with it, can't live without it! |
||
|
|
|
|
30-12-2008, 02:42 PM
|
#4 | ||
|
Tyre Shredn
Join Date: May 2007
Location: hillside
Posts: 162
|
cool beans. guys thanks for that
|
||
|
|
|
|
08-01-2009, 04:46 PM
|
#5 | ||
|
Tyre Shredn
Join Date: May 2007
Location: hillside
Posts: 162
|
as for oil pressure, go to pirtek and purchase a t-adapter for the oil pressure switch and fit the oil pressure sender into that. (next to oil filter on block)
is this the one above the oil filter??? |
||
|
|
|
|
08-01-2009, 07:29 PM
|
#6 | ||
|
Stroking it...
Join Date: May 2005
Location: The 'butt
Posts: 2,844
|
Umm, just to clarify, are we talking electronic gauges or mechanical???
Makes a little difference....
__________________
Had: 347ci AU Then:  Now: Busted assed EB Wagon - 5sp and Dual Fuel. |
||
|
|
|
|
11-01-2009, 12:50 PM
|
#7 | ||
|
Tyre Shredn
Join Date: May 2007
Location: hillside
Posts: 162
|
dont worry bout the last one done it.
as for the water sensor which hose does it go in top or bottom? which way does the water flow? from the bottom hose through the motor and out the top back to the radiator or is it the other way around??? |
||
|
|
|
|
11-01-2009, 09:40 PM
|
#8 | ||
|
Boost Addict
Join Date: Jan 2005
Location: North Brisbane
Posts: 1,151
|
top hose
__________________
N12 Pulsar - sold Gen1 Liberty Turbo - sold VP Commodore Turbo - sold LN65 Hilux Turbo - sold EL31 Corolla Turbo - sold Ford AU Ute Turbo - sold Ford AU XR8 Sedan - 5.4l V8 Turbo (in the build) Ford BA XR6T Ute - daily driver Ford FG XR6T Sedan - cruiser do you see a general trend? I DO Can't live with it, can't live without it! |
||
|
|
|
|
12-01-2009, 04:07 PM
|
#9 | ||
|
Tyre Shredn
Join Date: May 2007
Location: hillside
Posts: 162
|
yerp ok thanks
|
||
|
|
|
|
| Thread Tools | |
| Display Modes | |
|
|
How To Intsall Guages
Hybrid Mode