|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|
Thread Tools | Display Modes |
27-05-2010, 06:16 PM | #1 | ||
Regular Member
Join Date: Apr 2006
Posts: 282
|
OK, I have looked on the search function, and on the forums and to no avail.
This is the issue I have a 99 AU V8 Fairlane on dual fuel with 199000kms. It was running rough at idle on both petrol and LPG and then when accelerating it would not want to accelerate and run even rougher. The idle is that bad that the whole car shakes. I replaced the coil packs, spark plugs, and ignition leads. Cleaned K&N airfilter Checked wiring connections on engine Cleaned throttle body Cleaned contacts to airflow meter Changed oil and filter while I was there Changed fuel filter After all this the car still idled roughly and I took it for a drive and the acceleration was like it was still misfiring. I ran it on both petrol and LPG and it had the same symptons. When I got back in the driveway the car temp was at normal. I shut the car off and when I went to start it, it did not want to fire. I rechecked the leads and connections and they were all OK, out of desperation I gave the airflow meter a tap and the car started. It idled roughly and was backfiring. It seems the hotter the car gets the worse it becomes. Does anyone have any idea what to do next?? I have had the car towed to 2 mechanics and both of them could not find anything wrong with it
__________________
"I will keep it standard" I said. Yeah Right !!
1996 DF LTD - Standard cruiser (for now...) 1976 W114 Mercedes - Kustom with 302 V8 Windsor Project. Who knows what will happen..... |
||
27-05-2010, 08:07 PM | #2 | ||
Regular Member
Join Date: Sep 2005
Posts: 325
|
Common problem with AU V8, harmonic balancer it will cause it to miss, the more you drive it the rubber seal gets hot causing it to vibrate .
|
||
27-05-2010, 08:11 PM | #3 | ||
AULTD
Join Date: Mar 2005
Location: Langwarrin
Posts: 818
|
I had trouble after converting the V8 LTD to gas with it running rough on gas and petrol.
It wouldn't run properly on either fuel and it was like it was running on 4 cylinders It turned out to be the mixer. The gas guy took it off, pulled it apart and sprayed the inside with a carby cleaner. Every now and again it plays up and I just carefully take it apart and clean it myself. The system I have has an Impco mixer installed in the middle of the intake pipe. It seems it gums up every now and again and as it also affects the air getting to the engine it affects both the gas and petrol side of things. |
||
27-05-2010, 09:00 PM | #4 | ||
Regular Member
Join Date: Apr 2005
Posts: 284
|
I would check the harmonic balancer, if the crank angle ring is not right it wont run, and if the weight has shifted it will vibrate running.
|
||
28-05-2010, 08:09 PM | #5 | ||
Regular Member
Join Date: Apr 2006
Posts: 282
|
thanks guys, will try the harmonic balancer, seems to make sense
__________________
"I will keep it standard" I said. Yeah Right !!
1996 DF LTD - Standard cruiser (for now...) 1976 W114 Mercedes - Kustom with 302 V8 Windsor Project. Who knows what will happen..... |
||
28-05-2010, 11:23 PM | #6 | ||
FF.Com.Au Hardcore
Join Date: Jan 2008
Location: Sunbury, vic.
Posts: 3,110
|
although im not discounting it, but the ring on the harmonic balancer isn't connected to the rubber side it is part of the centre solid part, have seen many faulty and not one that has caused running issue's apart from bad shaking, particularilly bad at about 1300-1400rpm.
I'd be more inclined to check the actual sensor itself. |
||
28-05-2010, 11:31 PM | #7 | ||
FF.Com.Au Hardcore
Join Date: Feb 2005
Location: Melb north
Posts: 12,025
|
could it be getting gas and petrol causeing flooding? crank angle sensor?
|
||
29-05-2010, 01:32 PM | #8 | ||
AULTD
Join Date: Mar 2005
Location: Langwarrin
Posts: 818
|
I thought that was what mine was doing as it ran the same on gas and petrol.
It was the fact that the alloy part connected to the diaphram that lets the gas in doesn't move freely and blocks some of the air entering the engine and so starves it of air. Does your car have a mixer in the intake or just the ring like what is on the e-gas cars? |
||
29-05-2010, 08:11 PM | #9 | ||
Regular Member
Join Date: Apr 2006
Posts: 282
|
it has a mixer on the intake pipe.
this was checked by an lpg mechanic as well. The car is definitely idling roughly and extremely rough on acceleration. I will find how to chack the sensor first as it will be easier and if OK go the balancer route. Went to start it today and it has a flat battery so have put it on charge and with the weather we are having in Sydney I won't be able to test it until it clears up (the P6 LTD takes up both garages
__________________
"I will keep it standard" I said. Yeah Right !!
1996 DF LTD - Standard cruiser (for now...) 1976 W114 Mercedes - Kustom with 302 V8 Windsor Project. Who knows what will happen..... |
||
18-08-2010, 04:19 PM | #10 | |||
FORD-LOVER
Join Date: May 2010
Location: Melbourne, VIC
Posts: 173
|
Quote:
__________________
bf mk2.5 ego xr6 |
|||
Thread Tools | |
Display Modes | |
|