|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
19-07-2009, 04:52 PM
|
#1 | ||
|
Saving for a Jet Car
Join Date: Apr 2005
Location: richmond.nsw.au
Posts: 3,745
|
Just picked up a nudge bar to fit my new HID Spotties to.
These babies are going to out shine the sun :hihi: Looks like like Mechan1k's old one, as below Me, question is, has anyone self fitted one, are they easy enough to fit? Im hoping it will just bolt right up. I just need to see daylight long enough to do it too.... 
__________________
RIDES 2011 SZ Territory Titanium TDCi - Smoke 2001 Mitsubishi "BONSAI" GSR Mirage - see thread |
||
|
|
|
19-07-2009, 05:02 PM
|
#2 | ||
|
Banned
Join Date: Dec 2004
Location: searching for cubes
Posts: 6,672
|
You have to remove the front bar naturally, and some require a bit of cutting near the dummy vents. My TJM one went on without cutting, but I think the Bocar ones or ECB ones may need a small cut.
|
||
|
|
|
|
19-07-2009, 07:08 PM
|
#3 | ||
|
Miami Pilot
 
Join Date: Jan 2005
Location: ACT
Posts: 21,704
|
I've fitted an EL Falcon one to my explorer; few mods required, but not too hard. I've also undone one from an EL - they're pretty straight forward.
Ragtop has fitted one to his ute - might be worth a PM for tips.
__________________
-----------------------------------------------------------------
The Hammer: FG GTE | 376rwkw | 1/4 mile 11.793 @ 119.75mph 1.733 60' (4408lb) 1 of 60 FG MK1 335 GTEs (1 of 118 FG Mk 1 & 2 335 GTEs). Mods: Tune, HSD/ShockWorks, black GT335 19” staggered replicas with 245 & 275/35/19 Michelin Pilot sport 5s Daily: BF2 Fairmont Ghia I6 ZF, machine face GT335 19” staggered Replicas with 245s and 275s, Bilsteins & Kings FPV 335 build stats: <click here> Ford Performance Club ACT |
||
|
|
|
|
21-07-2009, 04:13 PM
|
#4 | ||
|
FF.Com.Au Hardcore
Join Date: Dec 2004
Location: ACT
Posts: 4,028
|
Definitely take the front bar off; I had to drill the holes to mount the brackets for the nudge bar; was a bit of mucking around, but got it sitting where I wanted.
Did you get all the mounting brackets, nuts and bolts?? |
||
|
|
|
|
22-07-2009, 08:54 AM
|
#5 | |||
|
Saving for a Jet Car
Join Date: Apr 2005
Location: richmond.nsw.au
Posts: 3,745
|
Quote:
Looks like a bumper off job, D'oh!
__________________
RIDES 2011 SZ Territory Titanium TDCi - Smoke 2001 Mitsubishi "BONSAI" GSR Mirage - see thread |
|||
|
|
|
|
22-07-2009, 10:13 PM
|
#6 | ||
|
Moderator
  
Join Date: Feb 2005
Location: Kenthurst
Posts: 40,403
 
|
I am pretty sure my front bar had to come off to get it fitted up.
I wasn't there when it was fitted to the ute. I had Tru-Racks in Penrith fit it for me (along with the driving lights) So unfortunately I didn't get a good look at the fitting ... they did trim back the dummy plates a fraction ... but it was still neat.
__________________
The Current Stable 2016 SZII TS Territory RWD Petrol The Evolution of the EGA54D utes AU Workshop Build thread of EGA54D B-Series Workshop Build thread of EGA54D 2004 SX TX Territory AWD - Gone but not forgotten 2010 FG XT "The ex-rental" - Moved onto a new home Mechan1k's Flickr Page |
||
|
|
|
|
| Thread Tools | |
| Display Modes | |
|
|
AU Nudge Bar
Linear Mode
