How to: Install rear courtesy light

[AUbigfoot]

This is a job that I completed today and thought I would share with others. Once you obtain the globe holder from a wrecker as ford is well expensive, it's an enjoyable mod to have providing you have the ignition barrel courtesy light. Please post any questions/feedback/complaints regarding this tutorial if you would like to Enjoy!!

Disclaimer: I take no responsibility for any damage or problems that may arise from you following the tutorial. It's merely a guide that I wanted to share after completing the task myself today.

How to: Install rear courtesy light
http://www.fordforums.com.au/showpos...7&postcount=72

[GK]

Nice work!

GK

[Uncle_Ken]

Originally Posted by GK

Nice work!

GK

As always, a man of few words (but accurate )
UK

[au11futura]

cool needed to see that as i got one for my au.

thanks mate.

[Beer Baron]

Good write up mate. IF your adding more than one light to the factory wiring i suggest using a relay so it doesn't load up the BEM so much.

[bartsau]

How ironic. I have just started doing this today. I have soldered up a complete loom for the footwell courtesy lights as well as the rear one in the back of the center console. Just going to finish it off tomorrow.

IF your adding more than one light to the factory wiring i suggest using a relay so it doesn't load up the BEM so much.

Question is as i am adding 3 lights to the ignition barrel light this will create a fair amount more load. I should know but what is a relay and how do you add this into the circuit??

[AUbigfoot]

Once that is answered, I will possibly add that to the tutorial for those doing more than what I did in my example
Thanks for the comments so far people!

[Halfmo Rocks]

Originally Posted by au11futura

cool needed to see that as i got one for my au.

thanks mate.

same here...i got the part with the light a while back (ebay bargain, 20 bucks or so - including postage)...never got around to getting a wire connected - what a great walk through...thanks bigfoot, most appreciated, though any further tutorial would of course be even better

[AUbigfoot]

Not bad, I sourced mine from a wreckers yard for $2 so it's 6 of one half dozen the other as to where you get them and how much you pay.
If I can be of any more help, just send me a message mate. I try to help where I can with my limited car knowledge haha

[Halfmo Rocks]

cheers mate, appreciate that.

i may well give it a try this weekend. i have had blue led's in most of the car...but have switched back to normal bulbs or white led's. my plan always was to have another blue light in this spot...but probably just go white.
the blue light means you can't see anything but blue in the car. had the blue interior dome light - tried to read a street directory one late night - difficult is a key word, looks sweet glowing blue in there...but doesn't help vision

[bartsau]

Ok so i know a little about circuits courtesy of the course i'm doing. I am on holidays so go gently on me.

The way i calculate it if you add 3 lights (both footwells and rear) to the ingnition barrel light you are adding a lot of current to the wiring. Now if i am correct and only if i then believe the added current may have the potential to heat the wires up and potentially cause problems down the track.

If you wired them up in series i think this may solve this but then the voltage drop accross the lights would make the last couple really dull.

Should i be concerned or not??

[illusivedreams]

If you wired them up in series i think this may solve this but then the voltage drop accross the lights would make the last couple really dull.

Sorry just a correction and Its been along time. I dont think the last few lights will be dimmer I think you will find the whole circut will dim as the lights will act as resistors but will be treated as one big resistor with adding more and more lights.

Will check

[illusivedreams]

Explanation – In a series circuit, the current going to each element (light bulb etc.) in the circuit goes through every element in order. If one element was to burn out, the entire circuit would burn out and no flow of electricity would result. If you add an extra element to this type of circuit, you will need to increase the voltage to have the same total voltage as before. If you remove an element out of this type of circuit, you will need to decrease the voltage to have the same total voltage as before. The following rules applying to Series Circuits.




1. The sum of the potential drops equals the potential rise of the source.
V(total) = V (1) + V (2) + V (3) + . . .



2. The current is the same everywhere in the series circuit.
I (total) = I (1) = I (2) = I (3) = . . .


3. The total resistance of the circuit is equal to the sum of the
individual resistances.
R (total) = R (1) + R (2) + R (3) + . . .



Applications

[RG]

Under the front passenger seat there is a flap in the carpet. Have a look under that and you should find the factory power wire for the rear courtesy light.

[Halfmo Rocks]

Originally Posted by RG

Under the front passenger seat there is a flap in the carpet. Have a look under that and you should find the factory power wire for the rear courtesy light.

interesting...i might look into that

[Whoosha]

Originally Posted by AUbigfoot

This is a job that I completed today and thought I would share with others. Once you obtain the globe holder from a wrecker as ford is well expensive, it's an enjoyable mod to have providing you have the ignition barrel courtesy light. Please post any questions/feedback/complaints regarding this tutorial if you would like to Enjoy!!

Disclaimer: I take no responsibility for any damage or problems that may arise from you following the tutorial. It's merely a guide that I wanted to share after completing the task myself today.

How to: Install rear courtesy light
http://www.fordforums.com.au/showpos...7&postcount=72

Great write up.. we will link it to the usefull threads as soon as we get 5 mins to spare

[AUbigfoot]

Thanks mate. I don't really understand an awful lot about cars so I try to help where things make sense to me!

[Halfmo Rocks]

Originally Posted by AUbigfoot

Thanks mate. I don't really understand an awful lot about cars so I try to help where things make sense to me!

i know that feeling...before i got my AUII, i knew how to change a tyre...and that's about it. i have learned things along the way, i have developed a passion for cars, and general car care in the 3 years i have owned it.

i am still learning, but loving it

[Wheelbarrow74]

How ironic. I have just started doing this today. I have soldered up a complete loom for the footwell courtesy lights as well as the rear one in the back of the center console. Just going to finish it off tomorrow.

Hey mate, Im just trying to replace the centre console courtesy light globe, but finding it a bit triky removing the back surround. I've undone the two screws located under the console lid, but not sure how its attached at the bottom near the carpet.. is it clips or screws? I don't want to go pulling and then bust it what's the trick?

[b2tf]

Originally Posted by Wheelbarrow74

Hey mate, Im just trying to replace the centre console courtesy light globe, but finding it a bit triky removing the back surround. I've undone the two screws located under the console lid, but not sure how its attached at the bottom near the carpet.. is it clips or screws? I don't want to go pulling and then bust it what's the trick?

It clips into the bottom of the centre console - you have to take the entire console out to get to it.