![]() |
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 | ||
FF.Com.Au Hardcore
Join Date: Mar 2005
Location: NSW
Posts: 1,802
|
Gday
Any one done a AU 4ltr timming chain cover removal for an oil leak repair,my wagon is starting to leak abit/alot between the head and the timming cover and looking at the haines manual,its a radiator,crank pulley,sump,engine mount,alternator a/c compressor off/out job. :togo: :togo: :togo: Surly its not that in depth is it.????????????
__________________
T2 TE50 no:154 Narooma blue AU2 XR8 ute XR4 fiesta |
||
![]() |
![]() ![]() |
![]() |
#2 | ||
Smile
Join Date: Dec 2004
Location: Merrylands Sydney
Posts: 8,541
|
Dunno man.mine leaks as well.I am going to try and wing it.Degreaser and then silicone the leaking area..
__________________
Stingray Car Security ph 0414445444 Single din radio fascias for fg to fgx fords Australia wide . FG 1 2 and 3 gauge holder in stock now! https://stingraycar.com.au/shop/ Site Sponsor See Sponsor Stingray Car Security 😍👌✌ AU wagon 6 14.241@96.75 1/4 mile sold.Octane fg xr6 turbo!! 12.312 112.21 mph home tune f6 injectors gone ..now in nitro fgxr6t ready to go again ![]() |
||
![]() |
![]() ![]() |
![]() |
#3 | |||
FF.Com.Au Hardcore
Join Date: Mar 2005
Location: NSW
Posts: 1,802
|
Quote:
If I have to go to the trouble of pulling all the accessories off,plus the sump,and radiator and unbolt the engine mounts,I may as well remove the engine and do every seal with it on the stand. 240k engine is it worth doing?????????
__________________
T2 TE50 no:154 Narooma blue AU2 XR8 ute XR4 fiesta |
|||
![]() |
![]() ![]() |
![]() |
#4 | ||
Smile
Join Date: Dec 2004
Location: Merrylands Sydney
Posts: 8,541
|
Nar man dont go to far.I fixed mine.Remove the belt,steeing pump ..do the correct procedure to remove the tensioner then chuck thread locker with silicone on the threads.It will fixit.
__________________
Stingray Car Security ph 0414445444 Single din radio fascias for fg to fgx fords Australia wide . FG 1 2 and 3 gauge holder in stock now! https://stingraycar.com.au/shop/ Site Sponsor See Sponsor Stingray Car Security 😍👌✌ AU wagon 6 14.241@96.75 1/4 mile sold.Octane fg xr6 turbo!! 12.312 112.21 mph home tune f6 injectors gone ..now in nitro fgxr6t ready to go again ![]() |
||
![]() |
![]() ![]() |
This user likes this post: |
![]() |
#5 | |||
FF.Com.Au Hardcore
Join Date: Feb 2005
Location: Melb north
Posts: 12,025
|
Quote:
|
|||
![]() |
![]() ![]() |
![]() |
#6 | ||
FF.Com.Au Hardcore
Join Date: Jul 2007
Location: perth w.a
Posts: 1,074
|
most just leak from the timing cover bolts so if ya just remove em one at a time clean them up and refit them with some sealant on the threads im pretty sure youl be fine hey ill fixed heaps of them doing this also check the chain tension bolt as well they also leak as does the front crank seal...its pretty rare for the actual gasket to be replaced....
|
||
![]() |
![]() ![]() |
![]() |
#7 | |||
Moderator
![]() ![]() Join Date: Feb 2005
Location: Kenthurst
Posts: 40,394
|
Quote:
It might just be your tensioner on the side of the engine. I makes it look like it leaks from around the front ... it makes a hell of a mess and hard to find the leak usually. I went on Stav's advice ages ago for this and it sorted it ... fingers crossed it is the same for you.
__________________
The Current Stable 2016 SZII TS Territory RWD Petrol The Evolution of the EGA54D utes AU Workshop Build thread of EGA54D B-Series Workshop Build thread of EGA54D 2004 SX TX Territory AWD - Gone but not forgotten 2010 FG XT "The ex-rental" - Moved onto a new home Mechan1k's Flickr Page |
|||
![]() |
![]() ![]() |
![]() |
#8 | |||
FF.Com.Au Hardcore
Join Date: Mar 2005
Location: NSW
Posts: 1,802
|
Quote:
thank you
__________________
T2 TE50 no:154 Narooma blue AU2 XR8 ute XR4 fiesta |
|||
![]() |
![]() ![]() |
![]() |
#9 | ||
FF.Com.Au Hardcore
Join Date: Mar 2005
Location: NSW
Posts: 1,802
|
ok,Ive gotten to the stage now ,I cant stand the site of oil every where under the bonnet,I removed all the tensioner bolts,even the power steer braket bolts and resealed them no difference,the leak seams to be worse on the a/c side of the unders side of the head,but when I start the thing and stick my head over the area,Im gettting flicked with oil,so Im thinking the front main is flicking it up and on the the belt and disbursing it everwhere under the bonnet.
I bought the timing cover seal kit,$11.95 which includes the front main seal,so at this stage every thing is coming out on Thursday. Ive got a manual radiator to replace the auto item and am going for the external only trans cooler whilst its out as well. I am concerned however with the lower timing chain guide as apparently these can fall into the sump when removing the cover as well as the locater dowels,any one got any ideas to make this not happen for me????? Its looking like a big job and Im not really looking forward to doing it the more I read and look into it. If I can get a mechanic to do it for less than $200 than the jobs his,if not,Im still contemplating pulling the engine and fitting a low k (60k engine for $300). and rebuild this engine latter on in my spare time............ any ideas would be appreciated
__________________
T2 TE50 no:154 Narooma blue AU2 XR8 ute XR4 fiesta |
||
![]() |
![]() ![]() |
![]() |
#10 | ||
Smile
Join Date: Dec 2004
Location: Merrylands Sydney
Posts: 8,541
|
Mate ..I degreased mine ..siliconed it and its been fine. Fixing these probs can be a can of darn worms..
__________________
Stingray Car Security ph 0414445444 Single din radio fascias for fg to fgx fords Australia wide . FG 1 2 and 3 gauge holder in stock now! https://stingraycar.com.au/shop/ Site Sponsor See Sponsor Stingray Car Security 😍👌✌ AU wagon 6 14.241@96.75 1/4 mile sold.Octane fg xr6 turbo!! 12.312 112.21 mph home tune f6 injectors gone ..now in nitro fgxr6t ready to go again ![]() |
||
![]() |
![]() ![]() |
![]() |
#11 | |||
FF.Com.Au Hardcore
Join Date: Jul 2007
Location: perth w.a
Posts: 1,074
|
Quote:
|
|||
![]() |
![]() ![]() |
![]() |
#12 | ||
FF.Com.Au Hardcore
Join Date: Mar 2005
Location: NSW
Posts: 1,802
|
ahhhhhhhhh,Ive just finished attempting to fix my oil leak(all day),Ive done today front main oil seal(fairly lengthy job),replaced the radiator as it had a slight leak ,fitted an external trans cooler..aaaaaaaaaaaaaannnnnnnnnnnnnnnnnnnddddddddd d i+ts still leaking,but now its all clean I can see where the oil leaks are coming from now the power steering bracket/screws which I have already removed and resealed,it looks like another day sorting that out tomorrow.....
Really accomplished nothing today ![]() ![]() ![]() if its still leaking tommorrow arvo,im ripping the engine out.......... ![]() ![]()
__________________
T2 TE50 no:154 Narooma blue AU2 XR8 ute XR4 fiesta |
||
![]() |
![]() ![]() |
![]() |
#13 | |||
FF.Com.Au Hardcore
Join Date: Apr 2005
Location: Moree, NSW
Posts: 2,076
|
Just wondering how you got one with your leaks.
__________________
Nathan 2005 FPV BF Super Pursuit The new toy (now sold) The SP The old ute (sold) www.aufalcon.com/nc1183 Build Thread Quote:
|
|||
![]() |
![]() ![]() |
![]() |
#14 | ||
FF.Com.Au Hardcore
Join Date: Mar 2005
Location: NSW
Posts: 1,802
|
yeh mate all sorted ,was just a mater of tightening the bolts really tight with a bit of thread sealant hasnt been a problem since
__________________
T2 TE50 no:154 Narooma blue AU2 XR8 ute XR4 fiesta |
||
![]() |
![]() ![]() |
![]() |
#15 | ||
Smile
Join Date: Dec 2004
Location: Merrylands Sydney
Posts: 8,541
|
Man what did it take to remove the timing case? I have a newfound leak..:( It is behind where the harmonc balancer is.
__________________
Stingray Car Security ph 0414445444 Single din radio fascias for fg to fgx fords Australia wide . FG 1 2 and 3 gauge holder in stock now! https://stingraycar.com.au/shop/ Site Sponsor See Sponsor Stingray Car Security 😍👌✌ AU wagon 6 14.241@96.75 1/4 mile sold.Octane fg xr6 turbo!! 12.312 112.21 mph home tune f6 injectors gone ..now in nitro fgxr6t ready to go again ![]() |
||
![]() |
![]() ![]() |
![]() |
#16 | ||
Starter Motor
Join Date: Feb 2006
Posts: 1
|
Hi All.
On the subject of oil leaks, I have one from the Tensioner Plug. In your experience, is this likely to be just a new o'ring on the plug, or would I need to go to the extent of getting deeper into the tensioner? Any risks in unscrewing this plug on it's own? Shane. |
||
![]() |
![]() ![]() |
![]() |
#17 | |||
FF.Com.Au Hardcore
Join Date: Mar 2005
Location: NSW
Posts: 1,802
|
Quote:
probly just the front main seal not an extremely hard job,pull the radiator/thermos,harmonic balancer,and pry the seal out, replace and grease it up every thing back togeather took me no more than 2 hrs. You need a good puller though. Its fun isnt it!!!!
__________________
T2 TE50 no:154 Narooma blue AU2 XR8 ute XR4 fiesta |
|||
![]() |
![]() ![]() |
![]() |
#18 | |||
Smile
Join Date: Dec 2004
Location: Merrylands Sydney
Posts: 8,541
|
Quote:
__________________
Stingray Car Security ph 0414445444 Single din radio fascias for fg to fgx fords Australia wide . FG 1 2 and 3 gauge holder in stock now! https://stingraycar.com.au/shop/ Site Sponsor See Sponsor Stingray Car Security 😍👌✌ AU wagon 6 14.241@96.75 1/4 mile sold.Octane fg xr6 turbo!! 12.312 112.21 mph home tune f6 injectors gone ..now in nitro fgxr6t ready to go again ![]() |
|||
![]() |
![]() ![]() |
![]() |
#19 | ||
Smile
Join Date: Dec 2004
Location: Merrylands Sydney
Posts: 8,541
|
what grease did you use?
__________________
Stingray Car Security ph 0414445444 Single din radio fascias for fg to fgx fords Australia wide . FG 1 2 and 3 gauge holder in stock now! https://stingraycar.com.au/shop/ Site Sponsor See Sponsor Stingray Car Security 😍👌✌ AU wagon 6 14.241@96.75 1/4 mile sold.Octane fg xr6 turbo!! 12.312 112.21 mph home tune f6 injectors gone ..now in nitro fgxr6t ready to go again ![]() |
||
![]() |
![]() ![]() |
![]() |
#20 | |||
Smile
Join Date: Dec 2004
Location: Merrylands Sydney
Posts: 8,541
|
Quote:
The car has hit 275000 kms
__________________
Stingray Car Security ph 0414445444 Single din radio fascias for fg to fgx fords Australia wide . FG 1 2 and 3 gauge holder in stock now! https://stingraycar.com.au/shop/ Site Sponsor See Sponsor Stingray Car Security 😍👌✌ AU wagon 6 14.241@96.75 1/4 mile sold.Octane fg xr6 turbo!! 12.312 112.21 mph home tune f6 injectors gone ..now in nitro fgxr6t ready to go again ![]() |
|||
![]() |
![]() ![]() |
![]() |
#21 | ||
FF.Com.Au Hardcore
Join Date: Mar 2005
Location: NSW
Posts: 1,802
|
yep,did it on my wagon,any grease is ok I use castrol PD2,or EP2 what ever was in the shed at the time,you just need to lubricate the lips otherwise they will burn/wear prematurely.You need to push the seal back in using the the crank bolt and spacer other wise its abit testing trying to get it started and square.
Are you sure its the front main seal though stav,mine turned out after doing all this to be the timming cover mount screws up the top and the oil was spitting/running down on to the timming casing making it look like it was the front main!!!!!! If you have your doubts do it any way as I said not a major job in my books anyway. Ha Ha yeh,mine is about to click over to 250k this week, and I think I better do the fuel pump,as she's missing abit on idle on fuel for a while on gas its fine
__________________
T2 TE50 no:154 Narooma blue AU2 XR8 ute XR4 fiesta |
||
![]() |
![]() ![]() |
![]() |
#22 | ||
Smile
Join Date: Dec 2004
Location: Merrylands Sydney
Posts: 8,541
|
I wish it was my timing case.Yep my first leak was my front power steering bolt and it needed alot of silicone to stop it. Next leak..loose timing case bolt.
Tommorow I may have a quick look behind my belt tensioner to see if there is a leak at the timing case. I had the head reinstalled at a dodgey wrecking yard which compromised the engine.It has little leaks which I am sealing slowly.If the car stops...then Il fix it.For now I hate the oil on my driveway.Not much but enough to make my steciling look ugly. What spacer did you use man?
__________________
Stingray Car Security ph 0414445444 Single din radio fascias for fg to fgx fords Australia wide . FG 1 2 and 3 gauge holder in stock now! https://stingraycar.com.au/shop/ Site Sponsor See Sponsor Stingray Car Security 😍👌✌ AU wagon 6 14.241@96.75 1/4 mile sold.Octane fg xr6 turbo!! 12.312 112.21 mph home tune f6 injectors gone ..now in nitro fgxr6t ready to go again ![]() |
||
![]() |
![]() ![]() |
![]() |
#23 | ||
FF.Com.Au Hardcore
Join Date: Mar 2005
Location: NSW
Posts: 1,802
|
It was about a 60mm 3/4 drive socket,it works perfectly with a long bolt in the from of the crank,dont forget to emery/sand/rough up the groove in the crank from the original oil seal.
__________________
T2 TE50 no:154 Narooma blue AU2 XR8 ute XR4 fiesta |
||
![]() |
![]() ![]() |
![]() |
#24 | ||
Sly like a G6
Join Date: Jun 2006
Location: Hunter Valley Whine Country
Posts: 1,808
|
I went to fix what I thought was a leaking timing chain tensioner the other day. On the way I found out that a workshop I used to trust had completely stripped the thread on the timing case where the lowest bolt shown goes. Oil was running out when I took the power steering bracket off.
![]() ![]() It's the one with all the copper RTV around it BTW! Does anyone know if there is enough metal in the timing case to put a Helicoil in?
__________________
The Frankenfalcon... AU1.5 Wagon, BA brakes, AU2 booster, BA2 XR6T engine, stock from airbox to turbo, 8psi/98 octane tune 240RWKW, BF XR6T cat, quiet 3" zorst, Pex BSO660 & BSO439 mufflers, 84 db, built BTR box, 3.08 LSD, Emer SVI LPG, AU1 XR8 alloys, Momo wheel, JVC KDR746BT head unit, Aerpro steering wheel control wiring. Sleeper, anyone? |
||
![]() |
![]() ![]() |
![]() |
#25 | ||
FF.Com.Au Hardcore
Join Date: Mar 2005
Location: NSW
Posts: 1,802
|
sly,yep thats the same bolt mine was leaking(one of the times anyway) your drilling into the block there not the case/alluminiun cover if you use a helicoil yes you can do it but DONT drill too far in as you'll drill into to no 1 cyl bore.
![]()
__________________
T2 TE50 no:154 Narooma blue AU2 XR8 ute XR4 fiesta |
||
![]() |
![]() ![]() |
![]() |
#26 | ||
Smile
Join Date: Dec 2004
Location: Merrylands Sydney
Posts: 8,541
|
Thats where mine leakt. When bolting it in it strips the thread alright.I would be defensive to helicoil as there may be a chance of dropping something into the engine wont it?
__________________
Stingray Car Security ph 0414445444 Single din radio fascias for fg to fgx fords Australia wide . FG 1 2 and 3 gauge holder in stock now! https://stingraycar.com.au/shop/ Site Sponsor See Sponsor Stingray Car Security 😍👌✌ AU wagon 6 14.241@96.75 1/4 mile sold.Octane fg xr6 turbo!! 12.312 112.21 mph home tune f6 injectors gone ..now in nitro fgxr6t ready to go again ![]() |
||
![]() |
![]() ![]() |
![]() |
#27 | ||
Sly like a G6
Join Date: Jun 2006
Location: Hunter Valley Whine Country
Posts: 1,808
|
So if it won't seal properly I'll need a new block... any other options?
__________________
The Frankenfalcon... AU1.5 Wagon, BA brakes, AU2 booster, BA2 XR6T engine, stock from airbox to turbo, 8psi/98 octane tune 240RWKW, BF XR6T cat, quiet 3" zorst, Pex BSO660 & BSO439 mufflers, 84 db, built BTR box, 3.08 LSD, Emer SVI LPG, AU1 XR8 alloys, Momo wheel, JVC KDR746BT head unit, Aerpro steering wheel control wiring. Sleeper, anyone? |
||
![]() |
![]() ![]() |
![]() |
#28 | |||
FF.Com.Au Hardcore
Join Date: Mar 2005
Location: NSW
Posts: 1,802
|
Quote:
A little trick I did with where your bolt is leaking is put an o-ring on the bolt with silicone. after you've repaired the thread that is
__________________
T2 TE50 no:154 Narooma blue AU2 XR8 ute XR4 fiesta |
|||
![]() |
![]() ![]() |
![]() |
#29 | ||
Regular Member
Join Date: Apr 2011
Posts: 111
|
Hi everyone. Put 60 k/km engine in au, got massive oil leaks! 2 litres in 2 weeks, barely driving also! Just when it gets up top, gonna do the clean, silicone, tensioner o rings, thread locker, I was playing around with old engine today, is it fine, to lock un lock cam tensioner with finger? Mine fits, lol does it sit on the last step not fully removed, in correct position? Why can't you remove outer thread nut without locking full ninety degree as in full lock position, new engine w.a.p.i.t.***!
![]() |
||
![]() |
![]() ![]() |
![]() |
#30 | ||
Missing a sock...
![]() ![]() Join Date: Mar 2012
Location: Brisbane 4017
Posts: 8,250
|
http://www.fordforums.com.au/showthread.php?t=11336109
Also I think Whoosha did a photo essay when he did his son's AU - I can't find it. Use the advanced search function. Doesn't look like a pleasant job, but then what is these days? Cheers!
__________________
Real friends + great times = sheer bliss! Considering becoming an organ donor? Click here QLD Events, Cruises and Get Togethers: Click here Gain success instantly - lower your standards. It's not government funded - it's taxpayer funded.
|
||
![]() |
![]() ![]() |
![]() |
Thread Tools | |
Display Modes | |
|