|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
07-02-2007, 08:08 PM
|
#1 | ||
|
Starter Motor
Join Date: Nov 2006
Posts: 16
|
Do you have to releave any part of the block to put in the 347 stroker kit in
and will the standard ecu run it. What type of cam should I use in a auto xr8 Is there any tricks or pittfalls in doing this type of conversion. Thanks |
||
|
|
|
07-02-2007, 08:13 PM
|
#2 | ||||
|
Back to Le Frenchy
Join Date: Feb 2005
Location: Back home.....
Posts: 13,346
|
Quote:
__________________
Quote:
07 Renault Sport Megane F1 Team R26 #1397
|
||||
|
|
|
|
07-02-2007, 08:18 PM
|
#3 | ||
|
Starter Motor
Join Date: Nov 2006
Posts: 16
|
I will building it my self. Why wont the standard ecu run it?
|
||
|
|
|
|
07-02-2007, 08:23 PM
|
#4 | ||
|
windsor user
Join Date: Dec 2004
Location: Geelong
Posts: 13,123
|
keep it fairly mild and the ecu will be fine......and then you have the AU Edit which will be fine with it when you want to go further...
yes you have to relieve the block........the rods will clip the bottom of the bores if you dont as above....add a few grand to what you think it'll cost...... |
||
|
|
|
|
07-02-2007, 08:25 PM
|
#5 | ||||
|
Back to Le Frenchy
Join Date: Feb 2005
Location: Back home.....
Posts: 13,346
|
Quote:
__________________
Quote:
07 Renault Sport Megane F1 Team R26 #1397
|
||||
|
|
|
|
07-02-2007, 08:30 PM
|
#6 | ||
|
windsor user
Join Date: Dec 2004
Location: Geelong
Posts: 13,123
|
yeah unichip isnt the best solution.........which is why i just sold mine...
should try the AU EDIT out..... ive heard it does wonders on the 8's ive bought for my car a mustang ECU (my car being pre smartlock, it was plug and play) and will be buying tweecer....(EEC edit) |
||
|
|
|
|
07-02-2007, 08:56 PM
|
#7 | ||
|
SS Grunt
Join Date: Oct 2005
Location: Melbourne-DEER PARK
Posts: 1,091
|
Ill try find a pic when i was building mine.
__________________
The Beast has gone to a new home Morpheous VE SS 6LTR 6speed Manual in its place, Leather, Lowered, 20's, Ramjet OTR and Dual 3inch, 280RWKW I will also enter any part of the Forum I wish to enter.  :
|
||
|
|
|
|
07-02-2007, 09:00 PM
|
#8 | ||
|
Banned
Join Date: Jan 2005
Location: Qld Moderator
Posts: 3,731
|
yes you will find that you will have to releive the block to clear the bottom of the rod. You machine shop should attend to this.
|
||
|
|
|
|
07-02-2007, 09:13 PM
|
#9 | ||
|
SS Grunt
Join Date: Oct 2005
Location: Melbourne-DEER PARK
Posts: 1,091
|
This was when i was installing cam bearings, you can clearly see the notch at the bottom of each bore, H-beams with cap screws as i used need a bit more then I beams.
__________________
The Beast has gone to a new home Morpheous VE SS 6LTR 6speed Manual in its place, Leather, Lowered, 20's, Ramjet OTR and Dual 3inch, 280RWKW I will also enter any part of the Forum I wish to enter. :
|
||
|
|
|
|
07-02-2007, 10:07 PM
|
#10 | ||
|
Starter Motor
Join Date: Nov 2006
Posts: 16
|
What type of cam can i use with the standard ecu and what power increase could I expect
|
||
|
|
|
|
09-02-2007, 11:14 AM
|
#11 | ||
|
Back on the road
Join Date: Dec 2004
Location: Wollongong, NSW
Posts: 3,205
|
The problem you will find with the std ECU, if it has not been re-calibrated with the edit, is that it is calculating load based on an engine displacement of 302ci. But being a 347, the EEC will be calculating a much higher load than the engine is actually doing.
At the end of the day, the EEC will command lower ignition advance than if it was properly tuned....which is real bad for power. The std injectors, and MAF will also be marginal on a mild 347. Thats why the T3's had a higher fuel rail pressure reg, and a larger 80mm MAF (although a 90mm MAF will work fine here as well)....again, you'll want to use the edit to reclibrate the std EEC for these changes as well. There might be more, but thats all I can think of for now.
__________________
------------------------------------------------------------------------- AU XR8 Ute 13.90 @ 100mph - http://www.aufalcon.com/xr8ute 5L Windsor, GT40X heads, Crane 2030, Pacey 4-1s, Lukey 3", 3.91:1, auto. Tuned by me w/Quarterhorse and BinaryEditor. Coming Soon: Ported lower intake, Tickford "Premium" Brakes, and a good wash. |
||
|
|
|
|
09-02-2007, 01:13 PM
|
#12 | ||
|
Starter Motor
Join Date: Nov 2006
Posts: 16
|
So Maybe I should leave it at 302 and just rebuild the bottom end and put a mild cam in and enjoy it as this is my company car I think 347 will take to long to sort out.
|
||
|
|
|
|
09-02-2007, 01:17 PM
|
#13 | ||
|
FF.Com.Au Hardcore
Join Date: Jan 2007
Location: taree
Posts: 583
|
Surely a few dollars thrown at it not getting it stroked will get a fair bit more performance from it?
Im not sure i havnt seen anyone just rebuild a tough 302 they all seem to stroke them. |
||
|
|
|
|
09-02-2007, 01:17 PM
|
#14 | |||
|
FF.Com.Au Hardcore
Join Date: Sep 2005
Location: Brisbane
Posts: 3,568
|
Quote:
|
|||
|
|
|
|
09-02-2007, 05:06 PM
|
#15 | ||
|
Starter Motor
Join Date: Nov 2006
Posts: 16
|
What would be the cost of the 331 stroker and will be better with the standard ecu.
I allready have 2 stroker motors and they do go very well but maybe a tough 302 is the go. are the standard rods and crank up to the task for more hp if so alloy heads and custom intake and cam would make more power. |
||
|
|
|
|
| Thread Tools | |
| Display Modes | |
|
|
stroker question
Linear Mode
