![]() |
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
![]() |
|
Thread Tools | Display Modes |
![]() |
#1 | ||
Regular Member
Join Date: Jun 2009
Location: Northern Suburbs, Mexico
Posts: 483
|
Hi I have an AU3 XR6 HP (non irs) and have a bit of an issue with the rear pads. The ones in the car are wearing weirdly, asif they do not have full contact with the rotor surface on the bottom 1/4. Eventually the Bottom 1/4 started making contact with the inside of the rotor. Now i have done some research and found standard AU2-3 rear pads are db1376 and AU2-3 xr6 are DB1354. Could the problem be wrong pads (Look identical to BA rears)? OR could it be Wrong rotors? As far as I can tell the car does not have the "tickford" upgraded brakes. The calipers themselves look similar to BA rears. Has anyone experienced this before or know which is the correct pads that should be in there?
__________________
Big dreams, not enough money ![]() Smoke tyres, not drugs ![]() ![]() |
||
![]() |
![]() ![]() |
![]() |
#2 | ||
FF.Com.Au Hardcore
Join Date: Aug 2006
Location: Salamander Bay
Posts: 5,427
|
DB1354 are for the Tickford premium brakes and you are correct about them being the same as BA rears
__________________
[SIGPIC][/SIGPIC]
Everyone starts off with a bag full of luck and an empty bag of experience. The trick is to fill the experience bag before the luck bag is empty. "It is better to remain silent and be thought a fool than to speak out and remove all doubt." Start a new career as a bus driver Rides: FG2 XR6 stock at this stage but a very nice ride xc 4 DOOR X CHASER 5.8 UNDER RESTO |
||
![]() |
![]() ![]() |
![]() |
#3 | ||
Next upgraded Mk1 Leopard
![]() Join Date: Jan 2005
Location: Sydney, in the burbs
Posts: 4,909
|
Got any pictures?
UK
__________________
Plastic Surgery 1 AUII Monsoon Blue How 2's: Change rear view mirror, Install backfire valve, Change foam front seats, Install auto transmission cooler, Replace Trans Shift Globe, Remove front door Trim, Paint AU headlights, install door spears, Premium Rear Parcel Shelf, go here...
|
||
![]() |
![]() ![]() |
![]() |
#4 | ||
Donating Member
![]() Join Date: Aug 2005
Location: St John's Park NSW
Posts: 1,454
|
Are the slides moving ok? What diameter are the rotors, 287mm? and solid type? If so, that is the standard size for AU II/III
|
||
![]() |
![]() ![]() |
![]() |
#5 | ||
Regular Member
Join Date: Jun 2009
Location: Northern Suburbs, Mexico
Posts: 483
|
I don't have any pics, forgot to take them when I had them apart and the discs are solid unsure of the diameter though. The slides seemed ok when had it apart. At this point I'm leaning towards possible wrong rotors. What are the correct discs? Db503's?
__________________
Big dreams, not enough money ![]() Smoke tyres, not drugs ![]() ![]() |
||
![]() |
![]() ![]() |
![]() |
#6 | ||
FF.Com.Au Hardcore
Join Date: Aug 2006
Location: Salamander Bay
Posts: 5,427
|
uneven wear can be caused by a worn sticking calliper exerting uneven pressure on the pad
__________________
[SIGPIC][/SIGPIC]
Everyone starts off with a bag full of luck and an empty bag of experience. The trick is to fill the experience bag before the luck bag is empty. "It is better to remain silent and be thought a fool than to speak out and remove all doubt." Start a new career as a bus driver Rides: FG2 XR6 stock at this stage but a very nice ride xc 4 DOOR X CHASER 5.8 UNDER RESTO |
||
![]() |
![]() ![]() |
![]() |
#7 | ||
Regular Member
Join Date: Jun 2009
Location: Northern Suburbs, Mexico
Posts: 483
|
__________________
Big dreams, not enough money ![]() Smoke tyres, not drugs ![]() ![]() |
||
![]() |
![]() ![]() |
![]() |
#8 | ||
Donating Member
![]() Join Date: Aug 2005
Location: St John's Park NSW
Posts: 1,454
|
You will need 2 DBA503 rotors and a set of DB1376 pads. If I were you I would also clean the caliper slides and re grease them before you put the pads and rotors in. Then after all that, bleed the brakes thoroughly front and rear.
![]() |
||
![]() |
![]() ![]() |
![]() |
#9 | ||
Regular Member
Join Date: Jun 2009
Location: Northern Suburbs, Mexico
Posts: 483
|
Yeah I didn't think the problem was the calipers so I will start with a set of rotors and pads but will also clean and grease the slides! Thanks for the replies so far!
__________________
Big dreams, not enough money ![]() Smoke tyres, not drugs ![]() ![]() |
||
![]() |
![]() ![]() |
![]() |
#10 | ||
FF.Com.Au Hardcore
Join Date: Dec 2004
Location: Perth NoR
Posts: 5,970
|
As Papa Smurf has mentioned.
FYI the DB1086, DB1354, and DB1376 are all essentially the same, they use identical backing plates only the friction material changes between all three part numbers. ![]() |
||
![]() |
![]() ![]() |
![]() |
#11 | ||
Regular Member
Join Date: Jun 2009
Location: Northern Suburbs, Mexico
Posts: 483
|
hmmm will keep this in mind also, thanks for the help everyone!
__________________
Big dreams, not enough money ![]() Smoke tyres, not drugs ![]() ![]() |
||
![]() |
![]() ![]() |
![]() |
#12 | ||
FF.Com.Au Hardcore
Join Date: Feb 2008
Location: Perth, Northern Suburbs
Posts: 4,924
|
Had a very similar issue on our AU3. Turns out it was the wheel bearing that was completely rooted (and I mean completely.) It was allowing the axle and rotor to move so much it was wearing on the calliper.
__________________
2024
Time to Make the Hippies Cry Again |
||
![]() |
![]() ![]() |
![]() |
#13 | ||
Regular Member
Join Date: Jun 2009
Location: Northern Suburbs, Mexico
Posts: 483
|
I've checked the wheel bearings and they are ok, also happend to both sides so thats why i was thinking rotors.
__________________
Big dreams, not enough money ![]() Smoke tyres, not drugs ![]() ![]() |
||
![]() |
![]() ![]() |