|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
10-02-2021, 08:15 PM
|
#1 | ||
|
Challenge Accepted!
Join Date: Jan 2006
Location: Under the Southern Cross
Posts: 882
|
I had the pleasure of removing the rear bumper on the folks MD. It all started with a Reverse sensor error that played up on a drive in the rain. The ole man got a tip to spray the sensors with wd40 and funny enough the error went away.
In any case it was going to be removed to check the harness and sensors. Two of the sensors had leaked wd40 behind the bumper and the rest were sealing as expected. Nothing was damaged or out of the ordinary so I had used sealant to seal it better and it's a wait and see during the next downpour. In any case it were simple as removing the spare tyre and lower inner boot trim, a small inspection side cover and just the rear portion or end of each side trim in the boot. Two nuts for each rear light assembly and one connection each and the lights are out. Then its about 18 screws (along the bottom and side up to the wheel arches) and 4 plastic rivits (2 each side) under the rear indicator housings. Now work the bumper from the bottom up and rearward to release the tab/clips and it's off, remember to remove the one harness connection to the rear sensors. And that's it. I was surprised with how much road chips and tar had been caught in the bumper and the fine dirt that settled in crevasses and creases. Was a good time to give it all a clean down. Without the bumper in place it looks like it has so much potential to look great but I thought that on the last Vehicle of theirs (Accord Euro Lux) that I removed the front bumper (another story) still the potential mmm mm m.       
__________________
Undecided replacement... [SOLD] -2009 MB Mondeo Zetec TDCI- [SOLD] |
||
|
|
|
10-02-2021, 08:41 PM
|
#2 | ||
|
Donating Member
 
Join Date: May 2008
Posts: 12,677
|
Interesting arrangement with the exhaust outlets.
__________________
PX MK II Ranger FG XR6 FG X XR8 Mustang GT T3 TS50 - gone but not forgotten |
||
|
|
|
10-02-2021, 09:02 PM
|
#3 | ||
|
Challenge Accepted!
Join Date: Jan 2006
Location: Under the Southern Cross
Posts: 882
|
yeah fake tips is an annoyance of mine and it's only getting worse across many manufacturers.
__________________
Undecided replacement... [SOLD] -2009 MB Mondeo Zetec TDCI- [SOLD] |
||
|
|
|
|
10-02-2021, 09:16 PM
|
#4 | |||
|
Donating Member
Join Date: May 2008
Posts: 12,677
|
Quote:
These tips are from the current Ford Explorer ST. I just don't see the point!    https://www.carthrottle.com/post/7-f...rs-look-cheap/
__________________
PX MK II Ranger FG XR6 FG X XR8 Mustang GT T3 TS50 - gone but not forgotten |
|||
|
|
|
|
10-02-2021, 09:44 PM
|
#5 | ||
|
Challenge Accepted!
Join Date: Jan 2006
Location: Under the Southern Cross
Posts: 882
|
Oh WOW! that's umm something else isn't it lol
__________________
Undecided replacement... [SOLD] -2009 MB Mondeo Zetec TDCI- [SOLD] |
||
|
|
|
|
10-02-2021, 09:47 PM
|
#6 | |||
|
Donating Member
Join Date: May 2008
Posts: 12,677
|
Quote:
__________________
PX MK II Ranger FG XR6 FG X XR8 Mustang GT T3 TS50 - gone but not forgotten |
|||
|
|
|
|
14-02-2021, 08:48 AM
|
#7 | ||
|
Challenge Accepted!
Join Date: Jan 2006
Location: Under the Southern Cross
Posts: 882
|
Well good news, the recent downpours continued and the sealant seems to have fixed the problem so far. Folks went out and were caught in the heavy thick of it and no issues.
I can only guess that water was affecting the sensor from reading objects, this in turn sent the error but also turned off blind spot monitoring and to a lessor extent auto parking feature and reverse sensor system. This wasn't a fix of any proportion only a checkup or removal and inspect but it's nice to have it working as it should.
__________________
Undecided replacement... [SOLD] -2009 MB Mondeo Zetec TDCI- [SOLD] |
||
|
|
|
2015 MD Ecoboost Titanium
Re: 2015 MD Ecoboost Titanium
Linear Mode
