Wheels That Fit Brembo Brakes

[irvinnie]

Versus talon 20x10 ET38 rears and 20x8.5 ET 35 fronts clear my 6/4 brembo's

[jamess]

Thanks for your help, I just picked up a set.

[d00bs]

GTE... Man that's a nice car.

[Kingkezza]

Any idea if the 20" staggered Lenso type F's clear Brembos?

https://www.facebook.com/30419257636...type=3&theater

[arronm]

Avant garde M550

[98TLS]

BBS 18 fit but only just,be lucky to slide a fag paper in between rim/caliper at the front...Edit...better pic,as you can see its only just.

[raised by monkeys]

Anyone had any experiences with hdlm garage wheels? A little JDM for some, but loving the INDT wheels

[Professor Farnsworth]

We need every compatible wheel so far compiled into a list in the OP!

[Toddy04XR6]

Has anyone got Lenso D1R rims on there car with 6 pot front 4 pot rears?

Thanks

[irvinnie]

The won't fit the rears in a staggered figment without using spacers

[malazn mafia]

Originally Posted by FLOORED

Vari 6 piston 362mm Factory clearance kit
The kit here is the VARI 362mm 6 piston kit and the caliper is made here in Australia and runs an internal dust seal (like AP Racing) and not external dust boots. The brake kit was fitted behind a 18" factory wheel with plenty of clearance and we should be able to do a smaller rotor as well. The kit is being tested on a BF ford and has had no issues at all. The rotors are available in 1 piece or 2 piece and will have 10 holes in the mounting pcd as we use the rotors for two different vehicles and brake kits which is not a problem because Audi and Subaru amongst others do the same thing. The front brake kits will sell for around the $2500 with a 1 piece disc and a 2 piece will be worked out later.
We will be checking it for FG vehicles and also checking for more wheel clearances with some help from our Ford customers.

Is there a brake kit for FG that equals or exceeds Brembos, but is able to fit any FG factory rim? I am looking to fit these http://m.ebay.com.au/itm/18-x-7-5-DE...293?nav=SEARCH wheels for a sleeper look, but the car needs to be able to brake as well as or better than an FPV with Brembos.

[kboot6]

Originally Posted by Toddy04XR6

Has anyone got Lenso D1R rims on there car with 6 pot front 4 pot rears?

Thanks

I believe the 20inch d1r fit over 6 pot. On my ute i have d1r 18s with 4 pot front. And i wouldnt go any smaller

[FLOORED]

Originally Posted by malazn mafia

Is there a brake kit for FG that equals or exceeds Brembos, but is able to fit any FG factory rim? I am looking to fit these http://m.ebay.com.au/itm/18-x-7-5-DE...293?nav=SEARCH wheels for a sleeper look, but the car needs to be able to brake as well as or better than an FPV with Brembos.

Short answer is no as the FG doesn't allow us to move the rotor in enough.

[phantom_87]

Stance sc5 clear 6 piston calipers 20× 8.5 size rim
Still yet to put the rear 4 piston calipers on

[FLOORED]

This was a current job we did fitting the Brembo 6/4 combo to some chrome wheels i hadn't seen before.

[phantom_87]

Finally got the rear 4 piston calipers on. I can confirm stance sc5 in 20×10 dont not clear the rear brakes.

[phantom_87]

Ok i swapped the 20x10 for a 20x8.5 eith 35mm offset and the now clear the rear 4 piston calipers

[Grippy]

Has anyone tried to fit BA XR 17's over 4 pot Brembo fronts? I spotted this BA XR6 Turbo track car at Phillip Island today with 4 pots squeezed under BA 17's. I'm wondering if he was running a smaller disk to make them fit? I'd love to run 17's on my Brembo equipped AU if they do indeed fit.

[Grum]

Yes, they fit. only OEM 17 that does.

Interesting car that one, I have done a bit of work on it in the past. How close a look did you have? It has a few secrets.

[Grippy]

Originally Posted by Grum

Yes, they fit. only OEM 17 that does.

Interesting car that one, I have done a bit of work on it in the past. How close a look did you have? It has a few secrets.

Thanks Grum, guess ill be keeping my Toyo R888 17's and hunting for a set of BA XR6 wheels.

I only had a quick look as the brakes caught my attention. From what I can tell it's one of 2 factory Ford Targa Tasmania entered BA XR6 Turbo's when released back in 2003.

[Grum]

Originally Posted by Grippy

Thanks Grum, guess ill be keeping my Toyo R888 17's and hunting for a set of BA XR6 wheels.

I only had a quick look as the brakes caught my attention. From what I can tell it's one of 2 factory Ford Targa Tasmania entered BA XR6 Turbo's when released back in 2003.

It was never a factory built road car. It was built as a prototype test car.

These are under the bonnet:

[FLOORED]

We also used to do a 336mm front rotor with a Brembo 4 pot back in the day.

[SIMBAD]

Originally Posted by Grum

Yes, they fit. only OEM 17 that does.

Interesting car that one, I have done a bit of work on it in the past. How close a look did you have? It has a few secrets.

Do the ba mk2 17" wheels fit as well?

[Grum]

Originally Posted by SIMBAD

Do the ba mk2 17" wheels fit as well?

Originally Posted by Grum

Yes, they fit. only OEM 17 that does.

Interesting car that one, I have done a bit of work on it in the past. How close a look did you have? It has a few secrets.

as above

[SIMBAD]

Originally Posted by Grum

as above

Ok cheers. The ba 17s fit and ba mk2 17s do not fit.

[dl86]

Originally Posted by FLOORED

No 17" wheels will clear the Brembo 355mm kits sorry and there are 17" wheels that will clear the PBR 325mm twin piston set up.
I haven't sold one in a while because everyone is fitting 355mm kits or larger BUT we have some 4 piston kits with either a AP Racing or Brembo caliper that use a 330mm to 336mm rotor that some 17" wheels fit over but these front kits generally cost about $3150 or so.

Not a street wheel but my 17x4.5" racestar front runners clear 355 Brembo's with ample room.

[WyldOne]

Can some with FPV GS rims 36.5 offset please confirm if they fit 6/4 brembos?

[Wolfinsheepsclothing]

Yes they sure do 100%

[unr33l]

Sure do:

[data_mine]

the GS rims originally came from the BF GT-P (standard with 6/4s)