|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
15-01-2007, 12:33 PM
|
#31 | ||
|
Smile
Join Date: Dec 2004
Location: Merrylands Sydney
Posts: 8,541
|
I dont know mate..This is the first electronic thingamabob I havent been able to work ever?
__________________
Stingray Car Security ph 0414445444 Single din radio fascias for fg to fgx fords Australia wide . FG 1 2 and 3 gauge holder in stock now! https://stingraycar.com.au/shop/ Site Sponsor See Sponsor Stingray Car Security 😍👌✌ AU wagon 6 14.241@96.75 1/4 mile sold.Octane fg xr6 turbo!! 12.312 112.21 mph home tune f6 injectors gone ..now in nitro fgxr6t ready to go again 
|
||
|
|
|
15-01-2007, 01:03 PM
|
#32 | ||
|
FF.Com.Au Hardcore
Join Date: Sep 2006
Posts: 2,981
|
It should, as it corrects the signal that is sent to the dash, which is then sent to the ecu
|
||
|
|
|
|
15-01-2007, 01:08 PM
|
#33 | ||
|
Smile
Join Date: Dec 2004
Location: Merrylands Sydney
Posts: 8,541
|
I know it should ..I must have used too much heat when I used my soldering station and internally fried the components.
__________________
Stingray Car Security ph 0414445444 Single din radio fascias for fg to fgx fords Australia wide . FG 1 2 and 3 gauge holder in stock now! https://stingraycar.com.au/shop/ Site Sponsor See Sponsor Stingray Car Security 😍👌✌ AU wagon 6 14.241@96.75 1/4 mile sold.Octane fg xr6 turbo!! 12.312 112.21 mph home tune f6 injectors gone ..now in nitro fgxr6t ready to go again
|
||
|
|
|
|
16-01-2007, 11:44 AM
|
#34 | |||
|
___________
Join Date: Jan 2005
Posts: 611
|
Quote:
|
|||
|
|
|
|
16-01-2007, 12:03 PM
|
#35 | ||
|
FF.Com.Au Hardcore
Join Date: Sep 2006
Posts: 2,981
|
It says it can adjust speed signal from 0-99% so it could be used to eliminate the speed limiter but obviously wouldn't be giving an accurate reading on dash whilst doing so
|
||
|
|
|
|
16-01-2007, 12:58 PM
|
#36 | ||
|
Regular Member
Join Date: Jun 2006
Location: Wollongong NSW
Posts: 419
|
you should be able to recalibrate the speedo if the cluster is in police mode. had loss some trip computer functions with police mode enabled.
|
||
|
|
|
|
16-01-2007, 02:10 PM
|
#37 | ||
|
Back in a Blue Oval
Join Date: May 2005
Location: Karratha WA
Posts: 707
|
my speedo needle when car is off sits about 10 mm under '0'. when the car turns on the needle taps itself down and up a few mm then resets to 0. Again turning off the car will see it tap itself a few times up and down before dropping 10mm back past 0. ??!!?? eh, at least it tells me tehe correct speed according to the diagnostics test mode.
the unfortunate part is my Tacho tells me the wrong revs. it sits at about 400 revs at idle (bleh) and rarely goes higher than 2000 in drive. i believe i caused these problems when i removed the cluster to replace the black fascia/decal(?) with a cheap as white piece of crap from ebay that melted 1 month later! trying to get the needles back on i thin i may have twisted them slightly whilst trying to put them on/pull them off. bugger. that's my 5 cents anyways
__________________
'13 Territory TX Diesel RWD. The Family Bus '08 Mitsubishi Pajero. The Off-road Machine |
||
|
|
|
Linear Mode
