Genuine Ford Parts - Page 23

arm79 · 08-02-2022, 10:40 PM

Quote:

Originally Posted by GTLEGEND

Hope this helps or maybe its confused you even further..

On the face of it it's like you've pushed my face further in the mud and given me a bigger headache all at once...

But reading through the list I can see some clarity that kind of matches what I thought.

My understanding on the BA you either had a knuckle with a fixed upper arm mount or an adjustable by cam bolt upper mount, which were on the XR's and FPV's. This would account for BA5A968A and BAT5A968A. I've seen the BAT part listed as adjustable.

But that was stopped in BF. The XR's got a fixed upper mount, which I figure is BAF5A968D, but the FPV bit in the description confuses me. BAF5A968C would be the adjustable upper knuckle, because that's what's in my Force 6. Plus the standard knucle.

Parts ending with B and E confuse me though. Something special about V8's and the Turbo. Given they had different diffs and half shafts, might have to do with the wheel hub. More splines maybe. But the FPV bit confuses me again.

Just spitballing...

Quote:

Originally Posted by GTLEGEND

If you pass on the VIN we may be able to narrow it down. I am guessing it would be 1st number.

The VIN on my Ghia is 6FPAAAJGSW6L56587, built 01/06.

As a comparison the VIN on Dad's XR6 is 6FPAAAJGSW6Y61571, built 02/06.

I'm having a problem where I'm getting insanely bad inner edge tire wear on the back tires. The alignment specs suggest the rear end is whatever whatever an XR is.

If it comes back with the standard part it will leave me even more confused. XR's have less than half the camber as base models and a very different toe setting. Then I will have to work out why the camber value is wrong. Is there something very out of wack in the rear end kind of thing.

And if its not the knuckle that is setting the camber the only other thing that it could be is the upper arm. But I'm told they are all the same.

GTLEGEND · 08-02-2022, 10:52 PM

Quote:

Originally Posted by arm79

On the face of it it's like you've pushed my face further in the mud and given me a bigger headache all at once...

But reading through the list I can see some clarity that kind of matches what I thought.

My understanding on the BA you either had a knuckle with a fixed upper arm mount or an adjustable by cam bolt upper mount, which were on the XR's and FPV's. This would account for BA5A968A and BAT5A968A. I've seen the BAT part listed as adjustable.

But that was stopped in BF. The XR's got a fixed upper mount, which I figure is BAF5A968D, but the FPV bit in the description confuses me. BAF5A968C would be the adjustable upper knuckle, because that's what's in my Force 6. Plus the standard knucle.

Parts ending with B and E confuse me though. Something special about V8's and the Turbo. Given they had different diffs and half shafts, might have to do with the wheel hub. More splines maybe. But the FPV bit confuses me again.

Just spitballing...

The VIN on my Ghia is 6FPAAAJGSW6L56587, built 01/06.

As a comparison the VIN on Dad's XR6 is 6FPAAAJGSW6Y61571, built 02/06.

I'm having a problem where I'm getting insanely bad inner edge tire wear on the back tires. The alignment specs suggest the rear end is whatever whatever an XR is.

If it comes back with the standard part it will leave me even more confused. XR's have less than half the camber as base models and a very different toe setting. Then I will have to work out why the camber value is wrong. Is there something very out of wack in the rear end kind of thing.

And if its not the knuckle that is setting the camber the only other thing that it could be is the upper arm. But I'm told they are all the same.

Rear knuckles per VIN:

6FPAAAJGSW6L56587: RH BA5A968A LH BA5A969A

Interesting next VIN drills down to two options but does not specify which one exactly possibly because the catalogue does not know exactly which one was put in your car.

6FPAAAJGSW6Y61571: RH BA5A968A or BAF5A968D, LH BA5A969A or BAF5A969D.

silverfern.kiwi · 09-02-2022, 01:10 AM

[QUOTE=GTLEGEND;6679502]

Quote:

Originally Posted by silverfern.kiwi

Hi Mike,

Is there any part numbers on the item especially one with 28560 or the alike in the middle of it.

Look at number 28560 in the pic below, is that what you are referring to.

Attachment 105325

sorry mate got picture off this forum but it does look the part

GTLEGEND · 09-02-2022, 07:16 AM

[QUOTE=silverfern.kiwi;6679668][QUOTE=GTLEGEND;6679502]
sorry mate got picture off this forum but it does look the part[/QU

That part I can get for $55 + freight which may be via courier as Aust Post will not send anything over 1M.

If you need those clips they are $18 each also.

Hope this helps..

Send a PM if you would like to order.

arm79 · 09-02-2022, 01:03 PM

Quote:

Originally Posted by GTLEGEND

Rear knuckles per VIN:

6FPAAAJGSW6L56587: RH BA5A968A LH BA5A969A

That's not what I was hoping for. Annoys the crap out of me and confuses me even more. Makes even less sense to me how I'm getting the alignment settings I'm getting.

Last question if I could...

Are the upper rear control arms all the same?

I always believed they were. But the only other things that could explain what I'm seeing is different length arms.

GTLEGEND · 09-02-2022, 02:29 PM

Quote:

Originally Posted by arm79

That's not what I was hoping for. Annoys the crap out of me and confuses me even more. Makes even less sense to me how I'm getting the alignment settings I'm getting.

Last question if I could...

Are the upper rear control arms all the same?

I always believed they were. But the only other things that could explain what I'm seeing is different length arms.

Yes only one upper control arm, LH/RH same as well. Part number BA5500A.

Rod · 11-02-2022, 01:22 PM

Are these FG Rims still available new

Numbers on the back are 8R29-1007-KA

I believe they are from an FG Tonner

GTLEGEND · 11-02-2022, 01:44 PM

Quote:

Originally Posted by Rod

Are these FG Rims still available new

Numbers on the back are 8R29-1007-KA

I believe they are from an FG Tonnerimage

Hi mate,

Yes they are, $440 each plus freight if required (guessing around $30 each in freight via Aust Post).

Rod · 12-02-2022, 03:36 PM

Quote:

Originally Posted by GTLEGEND

Hi mate,

Yes they are, $440 each plus freight if required (guessing around $30 each in freight via Aust Post).

Is that the right part number for them or is that just a casting number

gassa · 12-02-2022, 05:36 PM

Just enquiring if SY Territory Ghia rhs rear chrome outer weatherstrip belt line moulding is still available

Gassa

GTLEGEND · 12-02-2022, 06:24 PM

Quote:

Originally Posted by Rod

Is that the right part number for them or is that just a casting number

That is just the engineering number cast into the wheel..not the service part number.

GTLEGEND · 12-02-2022, 06:31 PM

Quote:

Originally Posted by gassa

Just enquiring if SY Territory Ghia rhs rear chrome outer weatherstrip belt line moulding is still available

Gassa

Hi Gassa,

Yes still available at $120 + postage if required.

Car must be a late build as they only came on those vehicles built after 1/4/2009.

GT

Rod · 15-02-2022, 10:55 AM

Quote:

Originally Posted by GTLEGEND

That is just the engineering number cast into the wheel..not the service part number.

Can you let me know the correct part number for this wheel

GTLEGEND · 15-02-2022, 12:51 PM

Quote:

Originally Posted by Rod

Can you let me know the correct part number for this wheel

Service part number is BG1007K..

arm79 · 15-02-2022, 11:21 PM

Quote:

Originally Posted by GTLEGEND

Yes only one upper control arm, LH/RH same as well. Part number BA5500A.

Hey mate. I forgot to come back to you earlier... But thanks for indulging in my curiosity and stupid questions and getting that info together for me!

GTLEGEND · 16-02-2022, 06:56 AM

Quote:

Originally Posted by arm79

Hey mate. I forgot to come back to you earlier... But thanks for indulging in my curiosity and stupid questions and getting that info together for me!

No problem, happy to help if I can..

2012Focus'd · 16-02-2022, 12:01 PM

Hi, I'm looking for a new cabin air temperature sensor for a 2012 Ford Focus. Are you able to quote?

GTLEGEND · 16-02-2022, 02:36 PM

Quote:

Originally Posted by 2012Focus'd

Hi, I'm looking for a new cabin air temperature sensor for a 2012 Ford Focus. Are you able to quote?

Is this for an LW1 or LW2 as 2012 is the change over, most probably no difference, but want to make sure. A VIN will help but not essential.

Also are you referring to the outside ambient temp sensor or the one that sits in the dash which is only for dual zone AC Auto temp controls or the one that sits inside the heater case? One controls Footwell the other face level..

**mad2** · 18-02-2022, 05:28 PM

Hi Legend

just a query with regards to parts numbers...... are the parts numbers the same for the BA/BF/SX/SY1 XR fog lights/covers?.

Thanks & take care.

GTLEGEND · 18-02-2022, 05:38 PM

Quote:

Originally Posted by mad2

Hi Legend

just a query with regards to parts numbers...... are the parts numbers the same for the BA/BF/SX/SY1 XR fog lights/covers?.

Thanks & take care.

Hey mate,

The BA/F XR Fog light covers fit Territory SX/Y from 1/2/2004 to 1/4/2009 and all share the same SX15K233AA part number.

Can get these for $54 plus freight if required.

The Spot/fog lights are also the same as above.

Part number RH: BA15K200A (obsolete from Ford), LH BA15K201A Can get for $150 plus freight if required.

**mad2** · 18-02-2022, 07:42 PM

Quote:

Originally Posted by GTLEGEND

Hey mate,

The BA/F XR Fog light covers fit Territory SX/Y from 1/2/2004 to 1/4/2009 and all share the same SX15K233AA part number.

Can get these for $54 plus freight if required.

The Spot/fog lights are also the same as above.

Part number RH: BA15K200A (obsolete from Ford), LH BA15K201A Can get for $150 plus freight if required.

Hi & thanks for the quick reply back. nah sorry as i was only after confirmation of the part numbers as i wanted to be sure they were the same. which they are.

Again many thanks

**mad2** · 18-02-2022, 10:14 PM

another question for you

what are the costs for the cap of the washer bottle to suit the BA/BF/SX/SY etc etc. postage to vic 3220.

Thanks

GTLEGEND · 18-02-2022, 10:45 PM

Quote:

Originally Posted by mad2

another question for you

what are the costs for the cap of the washer bottle to suit the BA/BF/SX/SY etc etc. postage to vic 3220.

Thanks

Part $18.50, postage would be around $3 with no tracking or $10 with tracking I think???

**DJM83** · 20-02-2022, 08:24 AM

Availability of this panel.

Also just checking again availability of XR6 badges for the sides of FG Ute

GTLEGEND · 20-02-2022, 10:40 AM

Quote:

Originally Posted by DJM83

Availability of this panel.
image
Also just checking again availability of XR6 badges for the sides of FG Ute

The top cover over the radiator support/radiator etc is still available. $60 plus freight if required (guessing no more that $20, but have no idea without dimensions, weight and forwarding post code).

As for the side badges they are currently out of stock but more coming soon. $70 each plus postage. I will see if I can get an ETA and advise.

GTLEGEND · 21-02-2022, 03:40 PM

For SGJ66. Parts 7 & 8?

AU V8 Water Pump.PNG

**DJM83** · 21-02-2022, 06:13 PM

Quote:

Originally Posted by GTLEGEND

The top cover over the radiator support/radiator etc is still available. $60 plus freight if required (guessing no more that $20, but have no idea without dimensions, weight and forwarding post code).

As for the side badges they are currently out of stock but more coming soon. $70 each plus postage. I will see if I can get an ETA and advise.

Depending on ETA with badges i might wait until i can get them to and order the lot.

GTLEGEND · 21-02-2022, 09:46 PM

Quote:

Originally Posted by DJM83

Depending on ETA with badges i might wait until i can get them to and order the lot.

ETA on badges are mid-March, but until they arrive I cannot be 100% certain.

I can keep an eye out and let you know or if you have not heard back from me by late March, give me a gentle reminder.

Peter l · 22-02-2022, 07:40 PM

Hi Need price for EB Wagon 7/91 Window Washer Bottle

GTLEGEND · 22-02-2022, 08:39 PM

Quote:

Originally Posted by Peter l

Hi Need price for EB Wagon 7/91 Window Washer Bottle

Hi there,

Sorry that part is long obsolete, part number EA17610C, but no longer available from Ford or dealers.

GT