Go Back   Australian Ford Forums > Club and Speciality Forums > Forum Community Car Clubs > OzECruisers (E/N/D Series) > OzECruisers General Discussions

OzECruisers General Discussions E/N/D vehicles General Discussion ONLY. NO TECH THREADS

Reply
 
Thread Tools Display Modes
Old 19-01-2005, 02:20 PM   #1
Yagz
Banned
 
Join Date: Dec 2004
Location: Melbourne
Posts: 522
Default Superlows and shocks

well, i changed the rear springs over to superlows, and it sits a *tiny* bit lower.. I'm going to give it a couple of weeks to settle..

The only criticism i have with the setup now, is that it's more bouncier than my pedders springs.. The pedders springs are also thicker than the superlows.. The old pedders used to handle bumps well, and stick to the road, but now it's alot more bouncy over bumps, etc..

Will a new set of monroe gt's fix this?

I'll get some pics up in a sec..

Last edited by Yagz; 19-01-2005 at 02:25 PM.
Yagz is offline   Reply With Quote
Old 19-01-2005, 02:32 PM   #2
Yagz
Banned
 
Join Date: Dec 2004
Location: Melbourne
Posts: 522
Default







ignnore the date, the camera shit itself ..
Yagz is offline   Reply With Quote
Old 19-01-2005, 03:14 PM   #3
oneredED
need more boost
 
oneredED's Avatar
 
Join Date: Jan 2005
Location: Melbourne
Posts: 1,143
Default

After replacing the shockers in mine, i can tell you that they're why it's bouncing all over the place. The difference is unbelievable, and i only put Monroe's in as well. Some good quality shocks and your beast should handle like a dream i would think ;)

Oh, and that'll drop at least an inch over the next month if those springs are brand new. Mine were "only just" secondhand, and they sagged a fairbit after a few weeks. If it still sits a bit high, make sure the springs are seated properly (i know you probably already have) because sometimes when i lower the car down (off the jack) they "unseat" themselves a little bit and sit slightly wrong raising one corner by 1/2 an inch...
__________________
'94 ED Falcon GLi
Suspended by: kings, koni, pedders
Rolls on: 17" AJR Director's
Stops due to: bendix, DBA
Shifter connected to: T5 manual
Power from: ???
Interior: velour and woodgrain
Cost: stuff all :P

Last edited by oneredED; 19-01-2005 at 03:24 PM.
oneredED is offline   Reply With Quote
Old 19-01-2005, 03:49 PM   #4
Yagz
Banned
 
Join Date: Dec 2004
Location: Melbourne
Posts: 522
Default

Quote:
Originally Posted by oneredED
After replacing the shockers in mine, i can tell you that they're why it's bouncing all over the place. The difference is unbelievable, and i only put Monroe's in as well. Some good quality shocks and your beast should handle like a dream i would think ;)

Oh, and that'll drop at least an inch over the next month if those springs are brand new. Mine were "only just" secondhand, and they sagged a fairbit after a few weeks. If it still sits a bit high, make sure the springs are seated properly (i know you probably already have) because sometimes when i lower the car down (off the jack) they "unseat" themselves a little bit and sit slightly wrong raising one corner by 1/2 an inch...
Ah, ok, how much are new shockers? Monroe GT's seem like the way to go..

These springs have been in a car for a couple of thousand kays, so i reckon they've done all the dropping they're gunna do.. It sits ok, and hopefully with new shocks, it'll sit even better..
Yagz is offline   Reply With Quote
Old 19-01-2005, 04:29 PM   #5
EFFalcon
Last warning
 
EFFalcon's Avatar
 
Join Date: Dec 2004
Location: Mornington Peninsula, Victoria HeadCount: 3
Posts: 11,194
Default

to me.. it seems a tad lower
hows the fuel load in those pics yagz?
__________________
FALCN6 - Turbo, Air Bag Suspension - Hibernating
EL GT - Supercharged
NASCAR - 83 Thunderbird , Bagged
DAILY - BA Fairlane Ghia, Boss 260 Turbo
OFFROADER - Ford Explorer
EFFalcon is offline   Reply With Quote
Old 19-01-2005, 05:36 PM   #6
NZ
~~~
 
NZ's Avatar
 
Join Date: Dec 2004
Location: At your U.B.
Posts: 2,099
Default

I just noticed something, do the xr alloys come in left and right or are they just a single design, because on one side of your car if you look at the top of the wheel the spokes point into the wind and the otherside they point away from the wind. Never actually noticed that before but it seems definitly weird
__________________
EF Falcon Sedan 5.0 auto with IRS

"the man that crashs AFF"
NZ is offline   Reply With Quote
Old 19-01-2005, 05:41 PM   #7
LUXO_8
windsor user
 
Join Date: Dec 2004
Location: Geelong
Posts: 13,123
Default

yeah 1 design, they never had 2 different rims on the car.....
spose you never look at both sides of the car at once


its called ford and the cost cutting they do.......
LUXO_8 is offline   Reply With Quote
Old 19-01-2005, 05:53 PM   #8
EFFalcon
Last warning
 
EFFalcon's Avatar
 
Join Date: Dec 2004
Location: Mornington Peninsula, Victoria HeadCount: 3
Posts: 11,194
Default

well what happens if u get the spare 5th alloy :P
THEN it would look weird if it was on the wrong side!
__________________
FALCN6 - Turbo, Air Bag Suspension - Hibernating
EL GT - Supercharged
NASCAR - 83 Thunderbird , Bagged
DAILY - BA Fairlane Ghia, Boss 260 Turbo
OFFROADER - Ford Explorer
EFFalcon is offline   Reply With Quote
Old 19-01-2005, 06:10 PM   #9
nothin suss
FF.Com.Au Hardcore
 
nothin suss's Avatar
 
Join Date: Jan 2005
Location: G-Town, VIC
Posts: 783
Default

Quote:
Originally Posted by EFFalcon
well what happens if u get the spare 5th alloy :P
THEN it would look weird if it was on the wrong side!
LOL.... : oh my...
__________________
PX3 Ranger - family truckster
BF Fairlong Ghia - boostlounge 11.26 @ 121
nothin suss is offline   Reply With Quote
Old 19-01-2005, 07:17 PM   #10
Yagz
Banned
 
Join Date: Dec 2004
Location: Melbourne
Posts: 522
Default

Quote:
Originally Posted by EFFalcon
to me.. it seems a tad lower
hows the fuel load in those pics yagz?
3/4 of a tank.. I hope it settles :(
Yagz is offline   Reply With Quote
Old 19-01-2005, 07:56 PM   #11
Damo
Banned
 
Join Date: Dec 2004
Posts: 4,078
Default

my wheels point in the right direction..
Damo is offline   Reply With Quote
Old 19-01-2005, 09:42 PM   #12
oneredED
need more boost
 
oneredED's Avatar
 
Join Date: Jan 2005
Location: Melbourne
Posts: 1,143
Default

Quote:
Ah, ok, how much are new shockers? Monroe GT's seem like the way to go..

These springs have been in a car for a couple of thousand kays, so i reckon they've done all the dropping they're gunna do.. It sits ok, and hopefully with new shocks, it'll sit even better..
Oh ok if they've been in the car a few thousand kays, then i'd say thats the height it will roughly stay. That's good though coz i like that height as it sits right now ;) Looks good! ...at least your rear aint lower than your front :
__________________
'94 ED Falcon GLi
Suspended by: kings, koni, pedders
Rolls on: 17" AJR Director's
Stops due to: bendix, DBA
Shifter connected to: T5 manual
Power from: ???
Interior: velour and woodgrain
Cost: stuff all :P
oneredED is offline   Reply With Quote
Old 19-01-2005, 09:45 PM   #13
oneredED
need more boost
 
oneredED's Avatar
 
Join Date: Jan 2005
Location: Melbourne
Posts: 1,143
Default

Looking at those pics again... that car should be waaaaay lower than it is if you've got superlows in the back. I wonder if there's something amiss here?
__________________
'94 ED Falcon GLi
Suspended by: kings, koni, pedders
Rolls on: 17" AJR Director's
Stops due to: bendix, DBA
Shifter connected to: T5 manual
Power from: ???
Interior: velour and woodgrain
Cost: stuff all :P
oneredED is offline   Reply With Quote
Old 20-01-2005, 12:22 AM   #14
Stevo
FF.Com.Au Hardcore
 
Join Date: Dec 2004
Location: Sth East Melb
Posts: 2,357
Default

Quote:
Originally Posted by Damo
my wheels point in the right direction..
Im trying to hunt down photo's at the moment, i think mine used to too ? (on the EF)
Stevo is offline   Reply With Quote
Old 20-01-2005, 12:27 AM   #15
JC
Miami Pilot
Donating Member2
 
JC's Avatar
 
Join Date: Jan 2005
Location: ACT
Posts: 21,703
Default

Yagz - the shocks should be about $120 for the pair, plus fitting. I've got the Monroe GT Reflex Techno things in mine, and they improved the handling and stopped the bounciness immediately - though i only have "lows" in the back, and superlows in the front.
__________________
-----------------------------------------------------------------
The Hammer: FG GTE | 376rwkw | 1/4 mile 11.793 @ 119.75mph 1.733 60' (4408lb)
1 of 60 FG MK1 335 GTEs (1 of 118 FG Mk 1 & 2 335 GTEs).
Mods: Tune, HSD/ShockWorks, black GT335 19” staggered replicas with 245 & 275/35/19 Michelin Pilot sport 5s

Daily: BF2 Fairmont Ghia I6 ZF, machine face GT335 19” staggered Replicas with 245s and 275s, Bilsteins & Kings

FPV 335 build stats: <click here>

Ford Performance Club ACT
JC is offline   Reply With Quote
Old 20-01-2005, 12:59 AM   #16
FPVWEPN
Team Urinal Cake Racing
 
FPVWEPN's Avatar
 
Join Date: Jan 2005
Posts: 1,075
Default

yagz i have superlows aswell and mine sits pretty much the same as yours maybe a little lower so thats what u should expect
FPVWEPN is offline   Reply With Quote
Old 20-01-2005, 12:02 PM   #17
galapogos01
eec tweaker
 
galapogos01's Avatar
 
Join Date: Jan 2005
Location: T.I. Performance HQ
Posts: 777
Default

they havent been in a car for a good few months, maybe 6.. so give em a week or so to settle.

looks about half an inch lower to me, but ive only seen the car once.. looked like a lot more gap between tyre and arch when i saw it the other day.

Jase
galapogos01 is offline   Reply With Quote
Old 20-01-2005, 12:28 PM   #18
Yagz
Banned
 
Join Date: Dec 2004
Location: Melbourne
Posts: 522
Default

Quote:
Originally Posted by galapogos01
they havent been in a car for a good few months, maybe 6.. so give em a week or so to settle.

looks about half an inch lower to me, but ive only seen the car once.. looked like a lot more gap between tyre and arch when i saw it the other day.

Jase
Yeah, don't get me wrong, it is lower, but i spose i expected it to be a bit lower, thats all.. I'm still very happy with the ride height!

I'm going to buy a set of monroe GT's as soon as dosh permits, to stop the bounciness..

Cheers guys,
yagz
Yagz is offline   Reply With Quote
Old 20-01-2005, 03:54 PM   #19
FRDXR6
FF.Com.Au Hardcore
 
FRDXR6's Avatar
 
Join Date: Dec 2004
Location: Melbourne
Posts: 975
Default

I think i need to get new shocks in the back to stop bouncing too, i already have kingspring all around and was thinking monroe gt at the back and the pedders shocks with lower seat postion at the front (as the front sits about an inch higher than the back), would that work alright?
FRDXR6 is offline   Reply With Quote
Old 20-01-2005, 06:46 PM   #20
oneredED
need more boost
 
oneredED's Avatar
 
Join Date: Jan 2005
Location: Melbourne
Posts: 1,143
Default

Quote:
I think i need to get new shocks in the back to stop bouncing too, i already have kingspring all around and was thinking monroe gt at the back and the pedders shocks with lower seat postion at the front (as the front sits about an inch higher than the back), would that work alright?
I was gonna do the same, but the pedders shocks with lowered seats aren't cheap. I ended up getting "lows" for the rear to bring it up instead. It does sit level with superlows, but only with no fuel (LPG or petrol) and no spare tyre. Bit impractical...
__________________
'94 ED Falcon GLi
Suspended by: kings, koni, pedders
Rolls on: 17" AJR Director's
Stops due to: bendix, DBA
Shifter connected to: T5 manual
Power from: ???
Interior: velour and woodgrain
Cost: stuff all :P
oneredED is offline   Reply With Quote
Old 30-01-2005, 07:10 PM   #21
oneredED
need more boost
 
oneredED's Avatar
 
Join Date: Jan 2005
Location: Melbourne
Posts: 1,143
Default

Sorry to dig this up guys, but I thought i'd let you know that the monroes i put in when this thread started are already buggered, well and truly. They squeak and carry on, and the ride is shithouse bouncing aorund like a pogo stick. Get some decent quality shockers if ya got superlows is all i can say...
__________________
'94 ED Falcon GLi
Suspended by: kings, koni, pedders
Rolls on: 17" AJR Director's
Stops due to: bendix, DBA
Shifter connected to: T5 manual
Power from: ???
Interior: velour and woodgrain
Cost: stuff all :P
oneredED is offline   Reply With Quote
Old 30-01-2005, 07:18 PM   #22
Kenaz
Donating Member
Donating Member1
 
Kenaz's Avatar
 
Join Date: Dec 2004
Location: Melbourne
Posts: 4,064
Default

Looks good Yagz How does it ride?
Kenaz is offline   Reply With Quote
Old 30-01-2005, 08:32 PM   #23
XRated
Shoot.
 
XRated's Avatar
 
Join Date: Jan 2005
Location: Melbourne
Posts: 4,909
Default

Quote:
Originally Posted by oneredED
Sorry to dig this up guys, but I thought i'd let you know that the monroes i put in when this thread started are already buggered, well and truly. They squeak and carry on, and the ride is shithouse bouncing aorund like a pogo stick. Get some decent quality shockers if ya got superlows is all i can say...
Ahhh that sucks Jarred. That's why I am waiting until I have enough funds for Konis :dj:
__________________


20V Turbo

XRated is offline   Reply With Quote
Old 30-01-2005, 10:53 PM   #24
xcursn
Guest
 
Posts: n/a
Default springs

hey,
ive jsut installed ultra lows all round in my ef xr6 with the standard shockers...got a great price $93 a pair at pakenham auto pro!! i must warn people not to do this... it is soo bouncy that i can get passengers to hit their heads on the roof on mild bumps doing 80 k's : .
so i have no learned that a good set of shockers is a must!!

i also have to ask. when i do get a set of lowered shocks will it lower my car even furthur?? because now it sits DAMN low..
  Reply With Quote
Old 30-01-2005, 11:12 PM   #25
EF302
FF.Com.Au Hardcore
 
Join Date: Jan 2005
Posts: 527
Default

Quote:
Originally Posted by xcursn
because now it sits DAMN low..
have u got any pics?
EF302 is offline   Reply With Quote
Old 30-01-2005, 11:32 PM   #26
MrFlibbles
ill have a beer milkshake
 
MrFlibbles's Avatar
 
Join Date: Jan 2005
Location: cardbboard box Adelaide Hills
Posts: 462
Default

i had kings super lows but took them out because rear passangers were hitting the roof over bumps,put in pedders big bore short stroke gsr shocks and the lowest pedders springs in rides much better only 10mm taller than kings super lows. part numbers are 2181 shocks gsr9180, not cheap but v nice ride
http://img.photobucket.com/albums/v6...6/DSC00233.jpg
MrFlibbles is offline   Reply With Quote
Old 30-01-2005, 11:33 PM   #27
MrFlibbles
ill have a beer milkshake
 
MrFlibbles's Avatar
 
Join Date: Jan 2005
Location: cardbboard box Adelaide Hills
Posts: 462
Default

lowered shocks/short stroke shocks will not change ride hieght...
MrFlibbles is offline   Reply With Quote
Old 30-01-2005, 11:44 PM   #28
LUXO_8
windsor user
 
Join Date: Dec 2004
Location: Geelong
Posts: 13,123
Default

sometimes they do especially on the front. depends if the spring saddle is in a different position (like the pedders and koni ones are)
LUXO_8 is offline   Reply With Quote
Old 30-01-2005, 11:49 PM   #29
svo347
AFF's 1st DM.......
 
svo347's Avatar
 
Join Date: Dec 2004
Location: Wha???... There is only 2 states 2 be in.. WA or Drunk..
Posts: 6,200
Default

With the stock springs they actaully drop about 30-40cm, The spring platform is lower!! combined with s/low springs , the height drops further.
94XR6 what rims are they?
got abetter pic by anychance.
__________________
FORD GIVING POWER TO THE PEOPLE
Alloy headed 347ci EDXR8
13.21 @107.7mph
Quote:
Originally Posted by zetec
I know what lengths they go to to ensure it's more than just a Ford sticker on the part. Ford doesn't throw it's name on anything for a quick buck.
06 Turbo Terri AWD 6 sp in Neo with stuff i didnt even need, side steps,15.2 inch roof mounted DVD,Pioneer $tezza,Selby 30/18mm swaybars,debunged,100 cpsi Ballistic cat,Plazmaman under battery Cai injectors 14/lb boost,ZF tuned,Xtreme's magic. :
svo347 is offline   Reply With Quote
Old 30-01-2005, 11:59 PM   #30
MrFlibbles
ill have a beer milkshake
 
MrFlibbles's Avatar
 
Join Date: Jan 2005
Location: cardbboard box Adelaide Hills
Posts: 462
Default

the pedders ones are only 25mm lower on the front with the repositioned platforms, i was assuming we were talking about the rear shocks, oh well i guess it pays not to assume anything! (ex pedders employee here)
MrFlibbles is offline   Reply With Quote
Reply


Forum Jump


All times are GMT +11. The time now is 04:37 AM.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Other than what is legally copyrighted by the respective owners, this site is copyright www.fordforums.com.au
Positive SSL