BOSS Junior at Calder

Craig · 10-12-2005, 10:12 AM

Took the Aussie Car Enhancements BA XT 220KW 3 Valve Manual Sedan out to calder last night, managed to fit in 3 runs with the following results.

1 = 14.60 @ 100.95, 2.43 60ft, Tyre spin central
2 = 13.81 @ 102.92, 2.33 60ft, Tyre spin not as bad
3 = 13.70 @ 102.64, 2.26 60ft, Tyre spin pretty ordinary.

This car is so different to drive compared to the XR8, the torque curve is killer down low and to get if off the line is difficult. Some more track time will be interesting with some good tyres (Chris i don't think i will be using your tyres next time thanks mate) and a LSD rear end would also be good.

out:

XRQTR · 10-12-2005, 10:19 AM

I love the whole sleeper look haha, especially when a couple of the guys in scrutineering asked if it was a company car :hihi:

xr8gn3 · 10-12-2005, 10:24 AM

Quote:

Originally Posted by BA Company Car

Took the Aussie Car Enhancements BA XT 220KW 3 Valve Manual Sedan out to calder last night, managed to fit in 3 runs with the following results.

1 = 14.60 @ 100.95, 2.43 60ft, Tyre spin central
2 = 13.81 @ 102.92, 2.33 60ft, Tyre spin not as bad
3 = 13.70 @ 102.64, 2.26 60ft, Tyre spin pretty ordinary.

This car is so different to drive compared to the XR8, the torque curve is killer down low and to get if off the line is difficult. Some more track time will be interesting with some good tyres (Chris i don't think i will be using your tyres next time thanks mate) and a LSD rear end would also be good.

out:

Awesome, I knew the 3v had the goods to run the times.

Gambit · 10-12-2005, 10:45 AM

That's a good time from the 220 motor. What tyres were you using?

Quadcams · 10-12-2005, 12:09 PM

Quote:

Originally Posted by BA Company Car

Took the Aussie Car Enhancements BA XT 220KW 3 Valve Manual Sedan out to calder last night, managed to fit in 3 runs with the following results.

1 = 14.60 @ 100.95, 2.43 60ft, Tyre spin central
2 = 13.81 @ 102.92, 2.33 60ft, Tyre spin not as bad
3 = 13.70 @ 102.64, 2.26 60ft, Tyre spin pretty ordinary.

This car is so different to drive compared to the XR8, the torque curve is killer down low and to get if off the line is difficult. Some more track time will be interesting with some good tyres (Chris i don't think i will be using your tyres next time thanks mate) and a LSD rear end would also be good.

out:

Mate get those 60' down to around 2.0 she will be doing quiet a good time, well done!

Craig · 10-12-2005, 06:35 PM

Quote:

Originally Posted by Gambit

That's a good time from the 220 motor. What tyres were you using?

Mickey Thompson Street Radials dude, they were on there last legs. The last run i did Chris said he could see sparks coming off the tyres as it left the start line cause the steel belts were coming out.....

**Chris** · 10-12-2005, 07:01 PM

dude, where's my tyres? lol

Craig · 10-12-2005, 07:50 PM

Quote:

Originally Posted by Chris

dude, where's my tyres? lol

lol, they are getting framed right now with a plaque that reads.

"Chris's lending out tyres to kick LS1 ****"

Sorry mate they are cactus..........................

rodderz · 10-12-2005, 07:56 PM

Thats great time for the 220 donk there Craig

Is there any figures on what torque that things putting out now?

galaxy xr8 · 10-12-2005, 08:35 PM

These little 220kw 3V's seem like a great little motor, good time and more to come by the sound's of it.

10-12-2005, 09:19 PM

Thats great!! If you could get those 60' time's down to flat 2s or even a 1.9 then it would be look out GT little brother's commin home!!
Your cars good for 13.5 pass for sure..

HEMI POWER · 10-12-2005, 09:52 PM

Quote:

Originally Posted by ELMER FUDD

Thats great!! If you could get those 60' time's down to flat 2s or even a 1.9 then it would be look out GT little brother's commin home!!
Your cars good for 13.5 pass for sure..

Elmer, these newer Generation of engines are just what Ford needed

: .Chris ran a flat 12 and now it's little brother into the 13's.Imagine what the 290 would do with a little more R&D.

:

outback_ute · 11-12-2005, 04:12 AM

Why imagine Alex???

Craig · 11-12-2005, 08:04 PM

Quote:

Originally Posted by rodderz

Thats great time for the 220 donk there Craig

Is there any figures on what torque that things putting out now?

Here's a link to the front page of my website with a scan of the dyno sheet. If youre ever in melton you need to drop in and take this thing for a drive cause they are so different to an XR8....

http://www.aussiecar.com/

rodderz · 11-12-2005, 08:11 PM

Might have to do that Craig, I'm up in melton a fair bit actually...seeing the aceXR8 cruising the streets too!

edit- dyno graph aint bad either!

CAMS290 · 11-12-2005, 08:15 PM

Well done Craig, its good to see a couple of people playing with these 3 valves.

SpoolMan · 11-12-2005, 08:19 PM

Quote:

Originally Posted by BA Company Car

Took the Aussie Car Enhancements BA XT 220KW 3 Valve Manual Sedan out to calder last night, managed to fit in 3 runs with the following results.

3 = 13.70 @ 102.64, 2.26 60ft, Tyre spin pretty ordinary.

Hi Craig, thats totally impressed me, awesome result and there is plenty of room for a time improvement on the 60 foot....
All you need is some good rubber...
Well done to all involved.

11-12-2005, 09:43 PM

Quote:

Originally Posted by BA Company Car

lol, they are getting framed right now with a plaque that reads.

"Chris's lending out tyres to kick LS1 ****"

Sorry mate they are cactus..........................

Improve those 60' times that car is a dead set 13.5 sec car now!! I wouldn't worry to much about tyres, I would be trying to get the 60' time down. There are plenty of GTs/XRs that get 2.0 60' times on street tyres "eg Dunlop sp 9000, theres plenty of time in that car yet..

:

Craig · 11-12-2005, 09:52 PM

Quote:

Originally Posted by ELMER FUDD

Improve those 60' times that car is a dead set 13.5 sec car now!! I wouldn't worry to much about tyres, I would be trying to get the 60' time down. There are plenty of GTs/XRs that get 2.0 60' times on street tyres "eg Dunlop sp 9000, theres plenty of time in that car yet..

:

The difference between an XR & GT'S on SP9000's and this thing is the car has a lot of low down torque that the others don't. GT'S and XR'S don't get moving until about 3000RPM where as the 3 valve is tough from the HIT.

The ET'S will come down once i get the start line figured out, will try again next friday night....

X ORSMXR · 11-12-2005, 10:12 PM

Well done Craig keep up the good work

ALS008 · 12-12-2005, 12:11 PM

Quite impressive results there Craig - when you get those 60's down, look out!!

XRQTOR · 12-12-2005, 01:16 PM

So it's running 13.7's on a single spinner.

Craig · 12-12-2005, 01:28 PM

Quote:

Originally Posted by XRQTOR

So it's running 13.7's on a single spinner.

Correct, 3.23 single spinner, hope to have LSD in by friday night.

XRQTOR · 12-12-2005, 01:46 PM

Quote:

Originally Posted by BA Company Car

Correct, 3.23 single spinner, hope to have LSD in by friday night.

So did you just have 1 slick or both on last friday night, should be an awsome result with an lsd and two slicks turning.

rodderz · 12-12-2005, 10:02 PM

Will the lsd still be the 3:23 Craig? Having so much torque from lower it may do better than an xr8 with the same ratio

Craig · 13-12-2005, 12:18 PM

Quote:

Originally Posted by XRQTOR

So did you just have 1 slick or both on last friday night, should be an awsome result with an lsd and two slicks turning.

Had the two on man, otherwise it would of looked like a sprintcar going down through there............

XRQTOR · 13-12-2005, 08:42 PM

Quote:

Originally Posted by BA Company Car

Had the two on man, otherwise it would of looked like a sprintcar going down through there............

Just stiring mate.

Craig · 14-12-2005, 08:54 PM

Quote:

Originally Posted by XRQTOR

Just stiring mate.

Yep i know you're stiring.

Got the LSD in tonight and the new rubber arrived this afternoon. Looks like i'm all set for friday night can't wait........

rodderz · 14-12-2005, 09:11 PM

Tried the textralia clutch Craig?

Craig · 14-12-2005, 09:25 PM

Quote:

Originally Posted by rodderz

Tried the textralia clutch Craig?

No mate the UTE is still sitting in the corner with no clutch i am waiting on the boys from textralia to get some bits from America to finish it off so we can try it out.

That's why i am playing with the 3 valve right now. That has a standard clutch hope it holds up for a little while yet, if it goes on friday night i will be riding my pushbike to work....