|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
18-05-2011, 08:50 PM
|
#1 | ||
|
Regular Member
Join Date: Feb 2011
Location: Melbourne - Eastern suburbs
Posts: 118
|
I might be going insane, but I keep looking and can't find the door light switch.
The interior lights come on with the other doors, but not my drivers door. Where is the drivers door light switch? Ross |
||
|
|
|
18-05-2011, 09:02 PM
|
#2 | ||
|
FF.Com.Au Hardcore
Join Date: Aug 2006
Location: Salamander Bay
Posts: 5,427
|
it is in the lock
__________________
[SIGPIC][/SIGPIC]
Everyone starts off with a bag full of luck and an empty bag of experience. The trick is to fill the experience bag before the luck bag is empty. "It is better to remain silent and be thought a fool than to speak out and remove all doubt." Start a new career as a bus driver Rides: FG2 XR6 stock at this stage but a very nice ride xc 4 DOOR X CHASER 5.8 UNDER RESTO |
||
|
|
|
|
19-05-2011, 08:09 AM
|
#3 | ||
|
Moderator
  
Join Date: Feb 2005
Location: Kenthurst
Posts: 40,403
 
|
Yeah it's all part of the lock actuator mechanism.
__________________
The Current Stable 2016 SZII TS Territory RWD Petrol The Evolution of the EGA54D utes AU Workshop Build thread of EGA54D B-Series Workshop Build thread of EGA54D 2004 SX TX Territory AWD - Gone but not forgotten 2010 FG XT "The ex-rental" - Moved onto a new home Mechan1k's Flickr Page |
||
|
|
|
|
19-05-2011, 07:55 PM
|
#4 | ||
|
Regular Member
Join Date: Feb 2011
Location: Melbourne - Eastern suburbs
Posts: 118
|
OK, thanks
Ross |
||
|
|
|
|
19-05-2011, 07:59 PM
|
#5 | ||
|
meh.
 
Join Date: Jul 2010
Location: Was Central Coast, Now Sydney NSW
Posts: 8,584
|
I had issues with the AU Wagon when the battery in the remote for the alarm went, to the point that I could unlock the door, get in and shut the door, and it wouldn't even recognise that I had just done so..
WD-40 fixed it
__________________
Previous - BF XR6T - 325rwkw, 6 Speed Auto, Process West, X-Force and Turbosmart gear |
||
|
|
|
|
19-05-2011, 08:14 PM
|
#6 | ||
|
Regular Member
Join Date: Feb 2011
Location: Melbourne - Eastern suburbs
Posts: 118
|
My interior lights come on if I unlock with the key fob, or key in door.
But if the car is unlocked and I open the drivers door, no light. If I open any of the other doors, light. xrghia, did you spray the keyfob or the lock with wd40? Ross |
||
|
|
|
|
19-05-2011, 08:18 PM
|
#7 | ||
|
meh.
Join Date: Jul 2010
Location: Was Central Coast, Now Sydney NSW
Posts: 8,584
|
I removed the entire lock mechanism from the door...
I ended up using over half a can just so I knew it should work..
__________________
Previous - BF XR6T - 325rwkw, 6 Speed Auto, Process West, X-Force and Turbosmart gear |
||
|
|
|
|
19-05-2011, 08:59 PM
|
#8 | ||
|
Regular Member
Join Date: Feb 2011
Location: Melbourne - Eastern suburbs
Posts: 118
|
OK, thanks
Ross |
||
|
|
|
|
04-09-2011, 10:02 PM
|
#9 | ||
|
Regular Member
Join Date: Feb 2011
Location: Melbourne - Eastern suburbs
Posts: 118
|
I tried to get the driver door trim off following the post by JC but I can't get the door lock knob off.
JC says "9. If drivers door, drop the trim down so the lock button pops up out of its housing - mark the position of the button on the wire thread with a felt tip pen. Unscrew the button.", but the lock button does not come out of its housing. Any other clues? Thanks Ross |
||
|
|
|
|
04-09-2011, 10:40 PM
|
#10 | ||
|
FF.Com.Au Hardcore
Join Date: Nov 2008
Location: Melbourne, Vic
Posts: 1,121
|
Not 100% sure but if your trying to get the actual lock knob that pops up when unlocked. I have always used a set of multigrips with the ends wrapped in tape to avoid damaging it. As for JC saying to mark it this a great idea. I had never thought of it before.
To do this I would think that you would simply pull the door trim off and lower it down so the rod the lock sits on protrudes beyond the door trim and then you can mark its position. Hope that makes sense.
__________________
AU III Forte wagon - V8, 5spd man, lowered, 18" Honeycombs, Stock diff rebuilt with TruTrac LSD, Leather Ghia interior/dash, custom twin 2.5" into single 3" exhaust. Wagon Build AU I Forte Sedan - No longer
Toy Car Build |
||
|
|
|
|
05-09-2011, 03:21 PM
|
#11 | |||
|
FF.Com.Au Hardcore
Join Date: Jul 2010
Posts: 859
|
Quote:
|
|||
|
|
|
|
05-09-2011, 08:33 PM
|
#12 | ||
|
Regular Member
Join Date: Feb 2011
Location: Melbourne - Eastern suburbs
Posts: 118
|
I actually got a pretty good grip on the button with just my thumb and fingers.
I pulled the button up as hard as I could, while pushing the door trim downward. The button and the surround both came out of the door trim but I couldn't see the rod to disconnect it. I guess I'll have to try pulling the button up whilst pushing its surround down. I guess that's why you need the multigrips. |
||
|
|
|
Door light switch
Linear Mode
