|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
28-11-2008, 11:19 PM
|
#1 | ||
|
2mny projects 2 lttl time
Join Date: Oct 2007
Location: Bald Hills Qld
Posts: 338
|
Is there a trick to removing the yoke from an AU2 XR6 4-speed auto box?
I was expecting it to just slide straight off as in the many times I've slid a tailshaft out, sometimes even when I didn't want to. But this one has a bare yoke, no tailshaft, so I don't have the weight advantage But it feels like theres something "solid" holding it in......don't wanna force it and break anything Advice please anyone??????? |
||
|
|
|
28-11-2008, 11:46 PM
|
#2 | ||
|
FF.Com.Au Hardcore
Join Date: Oct 2006
Location: Brisbane, QLD
Posts: 715
|
I'd like to know this also, as I need to replace mine very soon.
__________________
05 BF XR6 ZF 6spd - Stock for now Previously: 98 AU Futura 4.0 - Wildcat Extractors, 200cpsi Stainless Cat, Custom 2.5" Mandrel Bent Exhaust, Tickford Snorkel, Fram 'Airhog' Panel Filter - Daily
79 P6 LTD Silver Monarch - Project |
||
|
|
|
|
29-11-2008, 12:54 AM
|
#3 | ||
|
FF.Com.Au Hardcore
Join Date: Feb 2005
Location: Melb north
Posts: 12,025
|
if the other end is undone it should just slide out allthough sometimes there is a little suction .
|
||
|
|
|
|
29-11-2008, 01:14 AM
|
#4 | |||
|
2mny projects 2 lttl time
Join Date: Oct 2007
Location: Bald Hills Qld
Posts: 338
|
Quote:
|
|||
|
|
|
|
29-11-2008, 09:52 AM
|
#5 | ||
|
Boost Addict
Join Date: Jan 2005
Location: North Brisbane
Posts: 1,151
|
i assume its a 2nd hand gearbox you got and the yoke is put in as a plug? the yoke normally builds up some rust and at the point where it sits outside the rear seal, on transport they push the yoke in past its normall seating point and now the build up just gets stuck on the seal. give it a few gentle nocks with a hammer to loosen off if need be, but good chance that the seal will beno good afterwards one way or another
__________________
N12 Pulsar - sold Gen1 Liberty Turbo - sold VP Commodore Turbo - sold LN65 Hilux Turbo - sold EL31 Corolla Turbo - sold Ford AU Ute Turbo - sold Ford AU XR8 Sedan - 5.4l V8 Turbo (in the build) Ford BA XR6T Ute - daily driver Ford FG XR6T Sedan - cruiser do you see a general trend? I DO  Can't live with it, can't live without it! |
||
|
|
|
|
29-11-2008, 09:25 PM
|
#6 | ||
|
2mny projects 2 lttl time
Join Date: Oct 2007
Location: Bald Hills Qld
Posts: 338
|
Thanks guys. It came out fine.
I just didn't wanna break anything if Ford had decided to put a grubscrew in or something similar. Just being over cautious as the box was already sold. Thanks again |
||
|
|
|
| This user likes this post: |
AU2 auto g'box yoke remove
Linear Mode
