|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
10-11-2009, 04:40 PM
|
#1 | ||
|
Lurker
Join Date: Oct 2008
Posts: 39
|
Hey guys,
I'm sorry to be starting another post regarding bad starting, but I've just spent $500 on diagnostics with no fix. I'm hoping someone may have had a similar problem in the past. My XR6 VCT Ute (series 2) takes about 3 goes to start when cold. It starts fine, runs for about a second, and dies, about three times. On the third or fourth time it sustains, but struggles and idles badly for a few seconds. It starts first go when warm, but still a little rough. The following items have been checked: Ignition leads (replaced) spark plugs (replaced) crank angle sensor & cam angle sensor injectors (serviced) fuel rail and pressure fuel filter (replaced) IAC valve (cleaned) battery throttle body coil packs VCT system (as it has a vacuum connection to something) The only other thing I can think of is the engine computer. Which means my next move will be to have it removed and tested by Ford, an expensive exercise I'll bet. If anyone has any experience with bad starting that was not due to the above components, please let me know. |
||
|
|
|
10-11-2009, 05:00 PM
|
#2 | ||
|
AU XR6
Join Date: May 2007
Location: Morwell
Posts: 80
|
Have a go at resetting the computer first before you have it pulled out. There are a few discussions on here on how to do it.
|
||
|
|
|
|
10-11-2009, 05:55 PM
|
#3 | ||
|
Miami Pilot
 
Join Date: Jan 2005
Location: ACT
Posts: 21,704
|
You may need to replace the IAC valve - cleaning it doesn't always work.
Could also be leak in inlet manifold gasket (common issue) - try tightening the bolts up first, and see how that goes, but then I'd be looking for other vacuum hoses that have come off, and finally I'd change the IAC (borrow a known good one from a mate if you can, just to test that it is the problem - a new one is around $180 odd!).
__________________
-----------------------------------------------------------------
The Hammer: FG GTE | 376rwkw | 1/4 mile 11.793 @ 119.75mph 1.733 60' (4408lb) 1 of 60 FG MK1 335 GTEs (1 of 118 FG Mk 1 & 2 335 GTEs). Mods: Tune, HSD/ShockWorks, black GT335 19” staggered replicas with 245 & 275/35/19 Michelin Pilot sport 5s Daily: BF2 Fairmont Ghia I6 ZF, machine face GT335 19” staggered Replicas with 245s and 275s, Bilsteins & Kings FPV 335 build stats: <click here> Ford Performance Club ACT |
||
|
|
|
|
10-11-2009, 08:48 PM
|
#4 | ||
|
FF.Com.Au Hardcore
Join Date: Sep 2009
Location: Brisbane, Qld
Posts: 683
|
You can spray deodorant along the inlet manifold gasket and see if it helps it run better. Smells better than aerostart or carby cleaner.
__________________
AU XLS. |
||
|
|
|
|
24-11-2009, 05:15 PM
|
#5 | ||
|
Lurker
Join Date: Oct 2008
Posts: 39
|
Thanks guys, I took the car to Ford yesterday in Brisbane, they've apparently found an open circuit in the PCM causing no signal from the VCT unit. They've quoted $400 to repair (what is likely a five minute solder job) or $960 for a new computer. I wish I had my own tools and workspace- I'd fix it myself.
Thought I'd let everyone know about this as there are a number of 'bad starting' threads around. Of course- this may not really be the problem... |
||
|
|
|
AU XR6 VCT Stalling When Cold
Linear Mode
