|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
14-06-2010, 12:26 PM
|
#1 | ||
|
Regular Member
Join Date: Jun 2009
Posts: 245
|
Hi,
I have a problem when putting petrol into my AU1 where the fuel wont flow continuously, the trigger on the bowser handle keeps clicking when trying to fill up at every garage. Very frustrating. thanks. |
||
|
|
|
14-06-2010, 12:31 PM
|
#2 | ||
|
pursuit ute baby
Join Date: Jun 2010
Posts: 864
|
try positioning the nozzle back a bit, change the tilt.. sounds like youre getting splashback and the fuel sender unit thinks your tank it full.
|
||
|
|
|
|
14-06-2010, 12:32 PM
|
#3 | ||
|
FF.Com.Au Hardcore
Join Date: Feb 2008
Location: Geelong, Victoria
Posts: 4,503
|
Don't push the nozzle all the way in, have it just a bit inside the hole.
|
||
|
|
|
|
14-06-2010, 01:23 PM
|
#4 | ||
|
BA Xr8
Join Date: Feb 2005
Location: NZ
Posts: 917
|
Also look in the tank opening, you should have a flap (looks like a trap door) covering the opening that opens inwards when the nozzle is place in the tank. Sometimes this can come off and sit further down the tank opening causing this problem.
|
||
|
|
|
|
14-06-2010, 04:17 PM
|
#5 | |||
|
AFF Whore
Join Date: Apr 2009
Location: In between gas stations
Posts: 2,246
|
I have this problem just about every time I fill up, usually if I 'just' push the flap in, then start to fill its ok
__________________
Favorite Quote: Quote:
|
|||
|
|
|
|
14-06-2010, 05:07 PM
|
#6 | ||
|
Miami Pilot
 
Join Date: Jan 2005
Location: ACT
Posts: 21,704
|
I never have a problem when I fill up. But then mine's LPG.
Try jiggling the petrol nozzle around a bit and have it sitting just out (ie not all the way in).
__________________
-----------------------------------------------------------------
The Hammer: FG GTE | 376rwkw | 1/4 mile 11.793 @ 119.75mph 1.733 60' (4408lb) 1 of 60 FG MK1 335 GTEs (1 of 118 FG Mk 1 & 2 335 GTEs). Mods: Tune, HSD/ShockWorks, black GT335 19” staggered replicas with 245 & 275/35/19 Michelin Pilot sport 5s Daily: BF2 Fairmont Ghia I6 ZF, machine face GT335 19” staggered Replicas with 245s and 275s, Bilsteins & Kings FPV 335 build stats: <click here> Ford Performance Club ACT |
||
|
|
|
|
14-06-2010, 05:10 PM
|
#7 | ||
|
Cruising...
Join Date: Aug 2009
Location: Perth
Posts: 3,819
|
Its your AU telling you that it wants the premium stuff
__________________
FBT '98 BA XT '04 F100 4x4 '82 Subaru Outback '02 |
||
|
|
|
|
14-06-2010, 05:10 PM
|
#8 | ||
|
Never late with a V8
Join Date: Jan 2005
Location: Carrum Downs, Vic
Posts: 2,903
|
sounds like your breather could be blocked...
__________________
My Rides (Daily)2004 Explorer V8 Limited (Project/Cruiser)XE Fairmont Ghia- 351 Cleveland, Toploader (Work) 2014 Kenworth K200 Aerodyne (Classic) 1969 Mini K, 1340, twin SU's The beginning is near!!! Body by Ford. Soul by NudgE
|
||
|
|
|
|
14-06-2010, 05:54 PM
|
#9 | ||
|
Resident AFF detailer
Join Date: Dec 2008
Location: Melbourne, VIC
Posts: 3,730
|
IIRC Falcons have an S-bend at the start of the tube going into the fuel tank...
Turn the pump nozzle on a 45 deg angle next time you fill up, I've never had any problems with splashback doing this.....
__________________
No longer an 'active' detailer. |
||
|
|
|
|
14-06-2010, 10:01 PM
|
#10 | ||
|
Loving my '335' kW!
Join Date: May 2008
Location: Gold Coast, Queensland
Posts: 1,064
|
Seen this thousands of times managing servos, what I do is put it in the whole way, with some slight down pressure, then pull it out a little and wait for the nozzle to drop down. As soon as that happens, it should be in the optimum angle for a full fill.
Sounds like a dopey way, but sometimes it's hard to picture, and this is usually the easiest way of describing it.
__________________
FG X XR8 in Smoke. Smokin the tyres, that is! XR8 logo pic taken at Avalon Airport, Falcon Fanatic filming 17th October 2014 |
||
|
|
|
|
15-06-2010, 04:26 PM
|
#11 | ||
|
FF.Com.Au Hardcore
Join Date: Oct 2006
Location: Brisbane, QLD
Posts: 715
|
Mine only does that at one servo near me, all others are fine. I found rapidly 'pumping' the trigger repeatedly gets it to work, but as I said, thats only at this one servo.
__________________
05 BF XR6 ZF 6spd - Stock for now Previously: 98 AU Futura 4.0 - Wildcat Extractors, 200cpsi Stainless Cat, Custom 2.5" Mandrel Bent Exhaust, Tickford Snorkel, Fram 'Airhog' Panel Filter - Daily
79 P6 LTD Silver Monarch - Project |
||
|
|
|
|
15-06-2010, 11:03 PM
|
#12 | ||
|
Regular Member
Join Date: Oct 2006
Posts: 98
|
Mine had the same problem filling at all pumps. It started off doing it only only a few but got worse over time. The problem is with a little flap that Ford have fitted to the filler socket. It breaks off after a few years and catches in the filler tube,then the filling problem starts as the petrol back pressures trying to get past it. I used a piece of coat hanger wire with the end tightly bent over to hook the flap and then pull it up to the top of the filler socket. Onse you can see the flap, I used a pair of needle nose pliers (long nose should do it ok) and removed the flap. The car now fills to full without cutting off the bowser at all.
|
||
|
|
|
|
16-06-2010, 07:23 PM
|
#13 | |||
|
Regular Member
Join Date: Jun 2009
Posts: 245
|
I have tried not inserting the nozzle to far in, turning it in on an angle, still not working.
Quote:
|
|||
|
|
|
|
16-06-2010, 07:40 PM
|
#14 | ||
|
Steve
Join Date: Jun 2007
Location: Sth East Qld
Posts: 1,284
|
It is a fault with the anti siphoning flap in the top of the fill tube. My TE50 had the same problem ,it took ages to get a few bucks in . Search the T series room,I am sure there is something in there about it.
I had ford fix mine under used car warranty.
__________________
Currently no Fords . 2005 Statesman International 5.7, Mazda 2 and a Hilux. Former Fords: 2010 Ford Escape 2007 BF11 GT, TE50 Series 1 ,AU V8 One Tonner ,EL Falcon Wagon, ED Fairmont , EB Falcon Series 1. Mk 2 Cortina Company Fords : 3 BA Falcons , EB 11 Falcon Wagon , Ford F350 351 V8. |
||
|
|
|
|
02-09-2010, 11:37 AM
|
#15 | ||
|
Regular Member
Join Date: Jun 2009
Posts: 245
|
Yeah the flap was missing and also the tank was leaking so i picked up another tank and all problems fixed.
|
||
|
|
|
|
02-09-2010, 12:40 PM
|
#16 | ||
|
Regular Member
Join Date: Jun 2010
Location: melb , vic
Posts: 392
|
All sounds a bit porn related IMO
__________________
IF YOU CANT FIX IT WITH A SCREWDRIVER OR SHIFTER , F%$K IT with a hammer - Light travels faster than sound.......this is why some people appear bright until you hear them speak! AU SERIES 3 LIQUID SILVER BBS MOTORSPORT RIMS , EIBACHS , BILSTEINS , CERAMIC COATED 4499 PACIE'S , 2.5 S/S GENIE SYSTEM , MAGNAFLOWS , METALCAT 200cpsi , CAI MODS 123.4 GROUND TEARING RWKW'S , LOL |
||
|
|
|
|
03-09-2010, 12:18 AM
|
#17 | |||
|
FF.Com.Au Hardcore
Join Date: Feb 2008
Location: Geelong, Victoria
Posts: 4,503
|
Quote:
|
|||
|
|
|
Problem at the bowser.
Linear Mode
