|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
02-07-2006, 09:18 PM
|
#1 | ||
|
Regular Member
Join Date: May 2006
Location: Hobart
Posts: 76
|
Right then.
Let's say I got hold of a set of rocker covers for my Windsor and wanted to get tham painted up. What is the best wat to go about it and what is involved in removing the old ones/replacing them, as far as gaskets, etc goes? This is a new hobby for me, I'm not too familiar with this sort of stuff, to say the least. Cheers. |
||
|
|
|
02-07-2006, 10:05 PM
|
#2 | ||
|
Miami Pilot
 
Join Date: Jan 2005
Location: ACT
Posts: 21,704
|
I've got a set already painted in Black wrinkle/crinkle finish. Yours for $100 including postage.
Not too hard to swap them over - just a matter of undoing the 1/2 dozen or so bolts, and I just used the same gasket. Can't remember whether I need to remove the intake manifold, but I'm guessing I did.
__________________
-----------------------------------------------------------------
The Hammer: FG GTE | 376rwkw | 1/4 mile 11.793 @ 119.75mph 1.733 60' (4408lb) 1 of 60 FG MK1 335 GTEs (1 of 118 FG Mk 1 & 2 335 GTEs). Mods: Tune, HSD/ShockWorks, black GT335 19” staggered replicas with 245 & 275/35/19 Michelin Pilot sport 5s Daily: BF2 Fairmont Ghia I6 ZF, machine face GT335 19” staggered Replicas with 245s and 275s, Bilsteins & Kings FPV 335 build stats: <click here> Ford Performance Club ACT |
||
|
|
|
|
08-07-2006, 08:47 PM
|
#3 | ||
|
Blue to the bone!
Join Date: Jun 2005
Location: Sunshine Coast
Posts: 490
|
I'd like to see some pics of this if you get into it
|
||
|
|
|
|
08-07-2006, 10:58 PM
|
#4 | ||
|
Regular Member
Join Date: May 2006
Posts: 272
|
You'll have to remove your upper intake manifold to remove the rocker covers. It's pretty obvious what you'll need to do as you go along. If you are using cork gaskets then you'l need to clean the gasket residue of both the rocker covers and the head surface (be careful to keep gasket bits out of the heads) before fitting new ones. If you're using the metal and rubber resuable ones then no problems.
Painting is easy enough. Make sure they are well cleaned of grease etc, give them a light sand with wet/dry paper, another good wash and then paint the colour of your choice. It is possible to use most paints as the covers don't get that hot however engine paint is recommended as it will cure to a tougher finish. Better if you can pick up a spare set to prepare beforehand and then just change them over in one go rather than have your car off the road while doing your covers up. It just so happens there's a cheap set on eBay at the moment, hehe - click here. |
||
|
|
|
|
08-07-2006, 11:30 PM
|
#5 | |||
|
Regular Member
Join Date: May 2006
Location: Hobart
Posts: 76
|
Quote:
|
|||
|
|
|
Painting XR8 rocker covers - stupid question
Linear Mode
