|
|
|
|
|
|
Welcome to the Australian Ford Forums forum. You are currently viewing our boards as a guest which gives you limited access to view most discussions and inserts advertising. By joining our free community you will have access to post topics, communicate privately with other members, respond to polls, upload content and access many other special features without post based advertising banners. Registration is simple and absolutely free so please, join our community today! If you have any problems with the registration process or your account login, please contact us. Please Note: All new registrations go through a manual approval queue to keep spammers out. This is checked twice each day so there will be a delay before your registration is activated. |
|
|||||||
 |
|
|
Thread Tools | Display Modes |
19-05-2012, 06:59 PM
|
#1 | ||
|
Starter Motor
Join Date: May 2012
Location: Canberra
Posts: 5
|
Sorry if this has been covered before, I did a search but couldn't find it mentioned.
My 2001 AU Forte sedan suffers from the headlining drooping where it meets the front and back windscreens, literally 4 inches is hanging down. Has anyone had this problem and fixed it or had it fixed? It looks like glueing it up might help but the material is very thin so I'm wondering what type of glue to use? Thanks for any advice  Stewart Canberra |
||
|
|
|
19-05-2012, 07:26 PM
|
#2 | ||
|
Next upgraded Mk1 Leopard
 
Join Date: Jan 2005
Location: Sydney, in the burbs
Posts: 4,916
 
|
Yes it has been done but not easy to redo the whole lining. Have another look.
I just used some drawing pins as mine had not gone to far. So far so good. UK
__________________
Plastic Surgery 1 AUII Monsoon Blue How 2's: Change rear view mirror, Install backfire valve, Change foam front seats, Install auto transmission cooler, Replace Trans Shift Globe, Remove front door Trim, Paint AU headlights, install door spears, Premium Rear Parcel Shelf, go here...
 |
||
|
|
|
|
19-05-2012, 08:08 PM
|
#3 | ||
|
64 Deluxe 4 door
 
Join Date: Jun 2007
Location: Raxacoricofallapatorius
Posts: 10,446
|
I used spray on contact cement. worked a treat. just spray on the sagged bit and the lining, wait a bit. press it on and your set
__________________
XM Deluxe FG XR50 BA Pursuit Ute |
||
|
|
|
19-05-2012, 09:38 PM
|
#4 | ||
|
Starter Motor
Join Date: May 2012
Location: Canberra
Posts: 5
|
Thanks redxm, I'll give that a try.
Stewart |
||
|
|
|
|
19-05-2012, 10:50 PM
|
#5 | ||
|
FF.Com.Au Hardcore
Join Date: May 2009
Posts: 795
|
about $150-$170 you can have it professionally replaced and done in a couple of hours whilst one sits back sipping on a cool millers and lime!
__________________
http://i56.tinypic.com/23hlk6p.jpg |
||
|
|
|
|
24-05-2012, 03:17 PM
|
#6 | ||
|
Starter Motor
Join Date: May 2012
Location: Canberra
Posts: 5
|
Hmm, the 2 upholsterers I've contacted in Canberra so far are quoting $340, think I'll be relaxing with a glass of water....
|
||
|
|
|
|
24-05-2012, 04:00 PM
|
#7 | ||
|
Flairs - Truckers Delight
Join Date: Aug 2006
Location: Brisbane Northside Likes: Opposite Lock
Posts: 5,731
|
stewburt, keep on looking. try mobile guys too. if you're paying more than $190 for new rooflining in a sedan, you're getting had.
__________________
Current: Silhouette Black 2007 SY Ford Territory TX RWD 7-seater "Black Banger"
2006-2016: Regency Red 2000 AUII Ford Falcon Forte Automatic Sedan Tickford LPG "Millennium Falcon" |
||
|
|
|
|
24-05-2012, 08:29 PM
|
#8 | |||
|
FF.Com.Au Hardcore
Join Date: Jul 2011
Location: Topend of Oz since 1980
Posts: 5,299
|
Quote:
Darwin is a costly place for repairs but had mine replaced for $150 in under two hours with a life time warranty. |
|||
|
|
|
|
26-05-2012, 03:06 PM
|
#9 | ||
|
When in doubt, GAS IT!!
Join Date: Sep 2006
Location: Lower Eyre Peninsula, SA
Posts: 3,018
|
In my NF I just got spray glue, put a little slit in at the edge of the saggy bit and sprayed up inside all around through the hole. Gave it a couple of minutes then pressed it all back into place making sire to line up the lining where I put the slit. The only way it could be seen was if you new it was there. Just be sure you don't stretch the lining when you do it or you'll end up with a wrinkle somewhere.
Bushbasher
__________________
. HERS- BFIII Wagon Gold, alloys, dual fuel, bullbar, big tow pack, trans cooler, fully rebuilt HD suspension, Clarion, alarmed, full 2 1/2" sports system, mint body MINE- AUII Forte Meteorite, dual fuel but otherwise bog stock. MINE- AUII Fairlane Sportsman Liquid Silver over meteorite,HIDs', Airhog, Eagle Leads, dual fuel, custom rear springs, BA slotted discs + a second one for spares . |
||
|
|
|
|
26-05-2012, 03:20 PM
|
#10 | ||
|
FF.Com.Au Hardcore
Join Date: Feb 2008
Posts: 905
|
i got quoted 250 for a ute in SA :/
__________________
current ride: 92 Nissan GQ Patrol runs over 5h*T nuff said!! ED fairmont awaiting alot of parts and some love (v8 love) XF ute 4.0ltr injected out of an ed with girl cam and 5speed, and an xd front end for good measure |
||
|
|
|
|
26-05-2012, 04:10 PM
|
#11 | ||
|
FF.Com.Au Hardcore
Join Date: Feb 2010
Location: Gold Coast
Posts: 537
|
I saw an add on Gumtree for someone charging $100 (Gold Coast region). Not sure how high quality it will be, but I will be looking into it in the next few weeks (after I get this damn oil leak fixed)
|
||
|
|
|
|
29-05-2012, 07:50 PM
|
#12 | ||
|
FF.Com.Au Hardcore
Join Date: Jul 2010
Posts: 868
|
my xr6 had the same problem a tube or contact cement and problem fixed
|
||
|
|
|
AU series 2 drooping headlining
Re: AU series 2 drooping headlining
Linear Mode
